# OBD-II P0302: OBD-II P0302: Cylinder 2 Misfire Detected

> **Quick Answer:** Code **P0302** (SAE J2012) means the PCM detected crankshaft rotational deceleration on **Cylinder 2's power stroke** via its **Mode `$06` Cylinder 2 misfire counter**. **Safety rule: if the Check Engine Light is FLASHING, pull over and shut off the engine immediately**—raw unburned fuel pouring into the exhaust superheats and melts the catalytic converter within miles. Isolate the culprit in 10 minutes with a **component swap test**: move the **Cylinder 2 ignition coil** to Cylinder 1 or 3 (and if needed, move **Cylinder 2 spark plug** to a different cylinder). If the misfire jumps to **`P0301`** or **`P0303`**, replace the swapped part; if it stays on **#2**, check **fuel injector pulse/resistance** and **compression (`~120–180 psi`, within `10–15%` of adjacent cylinders)** ($25–$180 DIY; $140–$580 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0302
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Ignition & Misfire System
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
During every combustion event, the Crankshaft Position Sensor (`CKP`) tracks tiny rotational acceleration spikes. When Cylinder 2 fails to ignite or produces weak expansion, that brief deceleration increments the PCM's **Mode `$06` Cylinder 2 misfire counter**. Once misfire percentage threatens tailpipe emissions (steady CEL) or catalytic converter thermal safety (2-Hz **flashing CEL**), the PCM logs `P0302` and often cuts fuel to Cylinder 2.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| OBD-II Diagnostic Monitor | Mode $06 Cylinder 2 Misfire Counter | CKP angular velocity deceleration tracked per firing event |
| Healthy Compression Benchmark | ~120–180 psi (within 10–15% variance) | Values > 15% below adjacent cylinders point to valve/gasket/ring loss |
| Port Injector Coil Resistance | ~11–16 Ω (high-impedance PFI) | Verify injector pulse with noid light if coil & plug swaps stay on #2 |
| Flashing MIL Safety Threshold | Type A Catalyst-Damaging Misfire -> STOP | Unburned Cylinder 2 fuel causes catalytic converter meltdown |

## Commonly Affected Models & Service Bulletins
- Ford F-150 / Escape / Focus & Dodge/Jeep/Ram Pentastar 3.6L & HEMI Engines
- Toyota Camry / Corolla / RAV4 & Honda Accord / Civic / Odyssey Models
- Volkswagen / Audi 2.0T TSI, BMW N20/N55/B58 & Chevrolet/GMC Engines

## Common Symptoms
- Rough, shaking idle, vibration under acceleration, and clear lack of power
- **Steady or flashing Check Engine Light (`P0302`)**—flashing warns of active raw-fuel catalyst overheating
- Strong raw gasoline smell from the exhaust pipe and sharp fuel economy drop

## Most Likely Root Causes
- Failing **Cylinder 2 ignition coil (COP)**, cracked boot, or oil leaking into the #2 spark plug well (#1 most common)
- Worn, carbon-fouled, or cracked-insulator **Cylinder 2 spark plug** with excessive gap
- Clogged, leaking, or electrically open **Cylinder 2 fuel injector** or broken injector driver wire
- Low **Cylinder 2 compression** (burnt exhaust valve, blown head gasket, worn piston rings, or broken valve spring)

## Tools & Parts Reference
- OBD-II scan tool reading **Mode $06** live misfire counters
- Spark plug socket (`14 mm` or `16 mm`) with extension + torque wrench + feeler gauge
- Digital multimeter / noid light + mechanical **compression tester**

## Step-by-Step Troubleshooting & Fix
1. If engine oil coats the Cylinder 2 spark plug boot, replace the leaking **valve cover / plug-tube gasket** so fresh coils/plugs don't arc and short out.
2. Replace the failed **ignition coil** or **spark plug** confirmed by the swap test (replace all spark plugs as a matched OEM iridium/platinum set if near service interval and gap carefully without prying the fine electrode).
3. If `P0302` stays on Cylinder 2 with verified spark, replace a clogged/dead **Cylinder 2 fuel injector** or repair broken PCM ignition/injector harness pins.
4. If compression on Cylinder 2 drops `> 15%` below neighboring cylinders, perform a cylinder **leakdown test** to isolate a burnt valve, head gasket leak, or ring wear before mechanical engine repair.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $25–$180 | $140–$580 |
| GBP | £20–£145 | £115–£460 |
| CAD | CA$35–CA$240 | CA$185–CA$760 |
| EUR | €25–€165 | €125–€520 |
| CHF | CHF 35–CHF 220 | CHF 180–CHF 690 |

## Frequently Asked Questions
### Is it safe to keep driving when code P0302 causes a flashing Check Engine Light?
**No.** A flashing MIL signals a Type A catalyst-damaging misfire: unburned gasoline from Cylinder 2 ignites inside the red-hot catalytic converter, potentially destroying the converter (`$800–$2,000+`) or creating a fire hazard within minutes.

### Why should I move the coil and spark plug to two DIFFERENT cylinders during the swap test?
Moving Coil #2 -> #1 and Plug #2 -> #3 tests both parts in one single restart: if the code shifts to `P0301`, it's the coil; if it shifts to `P0303`, it's the plug; if it remains `P0302`, you immediately narrow the fault to Cylinder 2 fuel, wiring, or compression.


## Verified Official & Engineering References
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [California OBD-II Misfire Monitor Rules (13 CCR § 1968.2)](https://www.law.cornell.edu/regulations/california/13-CCR-1968.2) (Official Support)
