FaultCodes.org
P0175OBD-IIFuel Trim & Air/O2 MeteringVerified Guide· Updated: Nov 22, 2026

OBD-II P0175: System Too Rich (Bank 2)

SAE J2012 code set when Bank 2 adaptive Long Term Fuel Trim drops below -20% to -25% trying to lean out an over-fueled cylinder bank—check whether P0172 co-occurs to isolate global MAF/fuel-pressure/EVAP purge faults vs Bank 2 injectors or O2 bias.

Quick AnswerModerate — Plan Repair

Code P0175 (SAE J2012) means the ECM/PCM is pulling excessive fuel away on Bank 2 (the cylinder bank opposite cylinder #1 on V6, V8, or dual-bank inline-6 engines), triggering once adaptive Long Term Fuel Trim (`LTFT`) drops below `-20% to -25%`. First check whether `P0172` (Bank 1 Too Rich) is stored alongside P0175: `P0172 + P0175` together isolate a shared contaminated MAF sensor, excessive fuel rail pressure, stuck-open EVAP purge valve, or skewed ECT coolant sensor, whereas `P0175` alone pinpoints a leaking Bank 2 fuel injector, Bank 2 upstream O2 sensor stuck/biased lean, or Bank 2 ignition/airflow restriction. Inspect oil for raw fuel dilution and run fuel-pressure + MAF g/s checks before replacing sensors ($10–$220 DIY; $160–$560 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$160 – $560

What This Fault Code Means

To maintain a 14.7:1 stoichiometric air-fuel ratio for catalytic protection, the ECM continuously adjusts Short Term (STFT) and adaptive Long Term (LTFT) fuel trims based on upstream oxygen sensor feedback. When Bank 2 burns too much fuel or too little oxygen reaches combustion, the ECM subtracts injector pulse width until LTFT passes -20% to -25% and sets P0175.

Common Symptoms

  • Illuminated Check Engine Light (P0175 alone or paired with P0172), poor fuel economy, and raw gasoline exhaust smell
  • Black soot buildup inside tailpipes or fouled, carbon-black spark plugs on Bank 2 cylinders
  • Rough idle, sluggish throttle response, or hard hot restarts if a leaking injector floods Bank 2

Most Likely Root Causes

  • Over-reporting Mass Air Flow (MAF) sensor, stuck-open EVAP purge valve, or excessive fuel rail pressure (especially when P0172 + P0175 appear together)
  • Leaking or dripping Bank 2 fuel injector(s) or faulty Bank 2 fuel pressure regulator diaphragm
  • Bank 2 upstream O2 / A/F sensor biased or stuck lean (tricking the ECM into over-fueling Bank 2) or skewed Engine Coolant Temp (ECT) reading cold
  • Bank 2 ignition misfire (P030x leaving unburnt O2 + fuel) or severely clogged air filter / Bank 2 intake/exhaust restriction

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
SAE J2012 Rich Trim Threshold

ECM pulling maximum fuel away relative to 14.7:1 stoichiometric target

LTFT < -20% to -25% on Bank 2
Co-Code Isolation Matrix

Separates MAF/ECT/fuel pressure/EVAP purge from Bank 2 injector or B2S1 O2

P0172 + P0175 (Global) vs P0175 Alone (Bank 2)
Bank 2 Cylinder Location

Applies to V6, V8, horizontally opposed, and split inline-6 exhaust banks

Cylinder bank opposite Cylinder #1
Injector Leakdown Check

Rapid pressure drop or fuel-scented engine oil confirms leaking injector

KOEO rail pressure hold > 15 min

Commonly Affected Models & Service Bulletins

  • Ford / Chevrolet / GMC V6 & V8 Engines (MAF bias, EVAP purge & fuel pressure regulator faults)
  • BMW & Mercedes-Benz V6 / V8 / Dual-Bank Inline-6 Engines (leaky injectors & B2S1 A/F sensors)
  • Toyota / Lexus / Nissan / Chrysler V6 & V8 Platforms (SAE J2012 / EOBD)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Scan all DTCs and Freeze Frame data: determine if P0172 co-occurs with P0175 (shared global air/fuel fault vs Bank 2-isolated injector, O2, or ignition fault) and compare idle vs 2,500 RPM LTFT/STFT.
  2. 2Check live ECT temperature against ambient cold soak, verify MAF g/s airflow at warm idle (~1.0 g/s per liter of displacement), and pinch/block the EVAP purge solenoid hose temporarily while watching STFT climb back toward 0%.
  3. 3Measure fuel rail pressure key-on and leak-down hold over 15 minutes (rapid pressure bleed plus gasoline-smelling engine oil confirms a leaking injector), and inspect Bank 2 spark plugs and upstream O2 switching.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Do P0172 (Bank 1) AND P0175 (Bank 2) appear together alongside abnormal MAF g/s, cold ECT bias, or EVAP purge flow?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live-data scanner (Bank 1 & Bank 2 STFT/LTFT, MAF g/s, ECT, Freeze Frame)Fuel rail pressure gauge kit (static hold & running pressure test)MAF-safe sensor cleaner & pinch-off pliers (for EVAP purge isolation)
  1. 1Verify air filter cleanliness and clean a dirty MAF sensor wire/element only with dedicated MAF Sensor Cleaner, letting it dry 15 minutes completely.
  2. 2If pinching the EVAP purge line normalizes negative fuel trims, replace the stuck-open EVAP purge solenoid valve.
  3. 3If fuel rail pressure fails static hold or exceeds factory bar/psi specs, replace a ruptured fuel pressure regulator or pull and replace leaking Bank 2 fuel injector(s) (plus change fuel-diluted engine oil immediately).
  4. 4Resolve any Bank 2 misfires (P030x) or biased Bank 2 Sensor 1 O2/A/F sensor, clear codes, and confirm LTFT + STFT stabilize within ±10%.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$10 – $220
Professional Repair (Parts + Labor)$160 – $560

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

What does P0175 without P0172 tell a technician right away?

Because Bank 1 (P0172) runs normally while only Bank 2 (P0175) exceeds -20% to -25% LTFT, global parts like the air filter, MAF sensor, coolant sensor, and main fuel pump are usually innocent—focus immediately on Bank 2 injectors, Bank 2 upstream O2 sensor, or Bank 2 ignition.

Can driving long-term with P0175 damage the catalytic converter?

Yes. Unburnt excess fuel entering the hot Bank 2 catalytic converter causes runaway overheating that melts the ceramic substrate (P0430) and washes oil film off cylinder walls, diluting crank oil.

Related Searches & Questions

OBD2 P0175 system too rich bank 2 fixP0172 and P0175 together MAF purge valveP0175 alone without P0172 leaking injectorP0175 LTFT -25 percent diagnosis

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0175: System Too Rich (Bank 2) — Causes, Fixes & Cost | FaultCodes.org