FaultCodes.org
P0102OBD-IIFuel Trim & Air/O2 MeteringVerified Guide· Updated: Nov 22, 2026

OBD-II P0102: Mass or Volume Air Flow (MAF) Sensor "A" Circuit Low Input

SAE J2012 powertrain fault when the MAF signal drops below the hardware floor (`< 0.15–0.20 V` or near `0.0 g/s`)—usually caused by an unplugged connector, blown MAF fuse, open wire/short to ground, or oil-fouled hot-wire element.

Quick AnswerModerate — Plan Repair

Code P0102 (SAE J2012) means the PCM sees the Mass Air Flow (MAF) sensor signal voltage or frequency drop below the minimum hardware floor (`< 0.15–0.20 V`, reading near `0.0 g/s`) while the engine runs. Before buying a replacement sensor, verify the MAF connector is fully snapped in, inspect the intake boot for leaks, check the under-hood MAF/ECM fuse (12 V and 5 V supply + ground at the plug), and clean a dust- or oiled-filter-coated hot-wire element using dedicated MAF sensor cleaner spray ($10–$180 DIY; $160–$380 shop).

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$160 – $380

What This Fault Code Means

The MAF sensor measures incoming air mass (g/s) using a heated wire or film bridge (outputting roughly 0.5–1.0 V at idle up to 4.0–4.7 V at full throttle, or a calibrated Hz frequency on GM/Ford/Honda digital units). When the circuit drops below ~0.15–0.20 V (loss of 12 V heater/sensor power, broken signal wire, short to ground, or dead sensing bridge), the PCM substitutes calculated speed-density values and logs P0102.

Common Symptoms

  • Illuminated Check Engine Light (P0102, often paired with P0113 if the IAT wire shares the plug)
  • Hard starting, stalling right after startup, or sluggish acceleration / limp-mode hesitation
  • Black exhaust smoke, erratic automatic shifts, and poor fuel economy from fallback fueling

Most Likely Root Causes

  • Unplugged or loose MAF electrical connector after air-filter service or torn intake air duct
  • Blown MAF / Engine Sensor fuse or missing `12 V` / `5 V` reference supply & ground at the harness plug
  • Broken signal wire, short to ground, or backed-out pin inside the MAF harness
  • Heavy oil/dirt contamination on the MAF hot-wire element (from over-oiled aftermarket filters) or failed internal sensor bridge

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Hardware Low Voltage Floor

Signals open circuit, blown fuse, or short to ground below normal ~0.5–1.0 V idle

< 0.15–0.20 V (near 0.0 g/s)
Harness Supply & Reference

Verify at MAF plug KOEO before condemning the sensor body

12 V battery + 5 V ref + ground
Healthy Warm-Idle Airflow

Rough baseline equals ~1 g/s per liter at warm idle

~2.0–7.0 g/s (displacement scaled)

Commonly Affected Models & Service Bulletins

  • Nissan Altima / Sentra / Rogue & Infiniti (hot-film MAF fuse & connector faults)
  • Chevrolet Silverado / Equinox / Cruze & Ford F-150 / Focus (digital Hz & analog MAF)
  • Toyota Corolla / Camry / Tacoma & Volkswagen / Audi TSI engines (MAF contamination & wiring)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Pop the hood and check whether the MAF connector was left unplugged (P0102 + P0113 together is the classic sign) or if the airbox boot popped off after recent maintenance.
  2. 2Read live OBD-II MAF airflow (`g/s`) and sensor voltage: 0.0 g/s / < 0.15–0.20 V at KOEO or idle confirms a low-input circuit fault rather than a minor air leak.
  3. 3Unplug the MAF and probe the harness KOEO for `12 V` heater power, `5 V` reference (where equipped), and low-resistance sensor ground, checking the under-hood fuse box if power is 0 V.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Is the MAF plug disconnected, loose, or paired with P0113 right after an air filter change?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live-data scanner (monitoring MAF g/s & voltage/Hz)Digital multimeter & backprobe pins (12 V, 5 V, and ground verification)Dedicated aerosol MAF Sensor Cleaner & Torx/security screwdriver
  1. 1Reconnect any loose MAF plug until the locking tab clicks and tighten split intake hose clamps completely.
  2. 2If 12 V / 5 V power is missing at the harness, replace the blown MAF / Engine Control fuse and inspect wiring for chafing against brackets before re-powering.
  3. 3Spray the delicate MAF hot-wire/film cleanly with dedicated MAF Sensor Cleaner (never brake or carb cleaner, and never touch the wires), let dry 15 minutes, and re-test.
  4. 4If power and ground verify good yet signal stays < 0.15–0.20 V, replace the sensor with an OEM-grade MAF unit, clear codes, and verify ~2.0–7.0 g/s warm-idle flow (scaled by engine displacement).

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$10 – $180
Professional Repair (Parts + Labor)$160 – $380

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Can I clean a MAF sensor to fix P0102?

Yes, if oil residue or dust coats the hot wire, spraying only dedicated MAF Sensor Cleaner often restores response. However, if live data reads exactly 0.0 g/s (< 0.15–0.20 V), check for a blown fuse, unplugged plug, or dead sensor first.

Can I unplug the MAF sensor to test or drive home?

Temporarily unplugging a bad MAF forces the PCM into limp speed-density mode (P0102), which can verify whether an erratic MAF caused stalling—but avoid prolonged driving because fuel trims and transmission shift pressure become uncalibrated.

Related Searches & Questions

OBD2 P0102 MAF sensor circuit low input fixP0102 0.0 g/s fuse vs bad MAF sensorhow to test P0102 MAF 12V 5V groundP0102 after changing air filter

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0102: Mass or Volume Air Flow (MAF) Sensor… — Fixes & Cost | FaultCodes.org