FaultCodes.org
P0303OBD-IIIgnition & Misfire SystemVerified Guide· Updated: Nov 22, 2026

OBD-II P0303: Cylinder 3 Misfire Detected

Mode $06 Cylinder 3 misfire monitor triggered—swap Coil #3 -> #1/#2 and Plug #3 -> a separate cylinder to pinpoint coil vs plug vs injector/compression; check oil inside the #3 spark plug well (valve cover gasket) and stop immediately if the CEL flashes.

Quick AnswerHigh — Service Soon

Code P0303 (SAE J2012) means the PCM's Mode `$06` Cylinder 3 misfire counter detected repeated combustion misfires on Cylinder 3. Critical safety warning: if the Check Engine Light is FLASHING, stop driving immediately—raw fuel dumping out of Cylinder 3 can rapidly melt the catalytic converter. Diagnose accurately before buying parts by performing the two-cylinder component swap: move Cylinder 3 ignition coil -> #1 (or #2) and move Cylinder 3 spark plug -> a different cylinder. Also look inside Cylinder 3's spark plug tube for pooled motor oil from a leaking valve cover gasket, and if the fault remains on #3 after swapping, test fuel injector pulse/resistance and compression (`~120–180 psi`, within `10–15%`) ($25–$180 DIY; $140–$580 shop).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Ignition & Misfire System
Professional Repair
$140 – $580

What This Fault Code Means

On every compression/power cycle, the Crankshaft Position Sensor (CKP) measures rotational acceleration immediately after Cylinder 3 fires. When spark fails, fuel starves, or compression drops on #3, crankshaft speed lags momentarily and increments the Mode `$06` Cylinder 3 misfire counter, turning on a steady MIL (emissions level) or a flashing MIL (catalyst overheat threshold).

Common Symptoms

  • Rough idling, cabin vibration, hesitation on throttle tip-in, and loss of hill-climbing power
  • Steady or flashing Check Engine Light (`P0303`)—a flashing light requires immediate engine shutdown
  • Raw gasoline smell from exhaust and sharp drop in fuel mileage

Most Likely Root Causes

  • Failed Cylinder 3 ignition coil (COP) or oil-soaked rubber coil boot leaking spark to ground (#1 cause)
  • Engine oil flooding the #3 spark plug well through a hardened valve cover / tube seal gasket
  • Worn, cracked, or fouled Cylinder 3 spark plug or clogged/dead Cylinder 3 fuel injector
  • Mechanical Cylinder 3 compression loss (burnt valve, blown head gasket, or worn piston rings)

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
OBD-II Counter Channel

Tracks rotational deceleration specifically on Cylinder #3 firing window

Mode $06 Cylinder 3 Misfire Counter
Compression Specification

Confirms valve, head gasket, and ring integrity when spark/fuel test good

~120–180 psi (within 10–15% spread)
Injector Resistance (PFI)

Check connector power and ground switching if swap stays on #3

~11–16 Ω + crisp noid-light pulse
Flashing MIL Protection Rule

Prevents raw fuel catalyst meltdown and exhaust fire hazard

Shut down engine immediately on flashing CEL

Commonly Affected Models & Service Bulletins

  • Honda Accord / Civic / CR-V & Subaru Forester / Outback (plug-tube seal leaks & coils)
  • Ford F-150 / Explorer / Escape & Jeep/Dodge/Chrysler 3.6L V6 & 2.4L Engines
  • Toyota Corolla / Camry / Highlander, Nissan & VW/Audi/BMW 4- and 6-Cylinder Engines

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Verify whether the MIL is steady or flashing (shut down immediately if flashing), check Mode $06 Cylinder 3 misfire counts, and pull the #3 ignition coil to inspect the plug well for pooled oil or coolant/moisture.
  2. 2Swap Coil #3 -> Cylinder #1 (or #2) and move Plug #3 -> another cylinder (e.g., #4) on separate cylinders, clear P0303, and idle/test briefly: if the code shifts to P0301/P0302, replace the coil; if it shifts to P0304, replace the spark plug.
  3. 3If misfire counts stay fixed on Cylinder 3, check #3 injector wiring & coil resistance (`~11–16 Ω` port injection) with a noid light/multimeter and measure compression (`~120–180 psi`, max `10–15%` spread).

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Is engine oil pooled inside the Cylinder 3 spark plug well soaking the ignition boot?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live scanner with Mode $06 misfire count trackingSpark plug socket (14 mm / 16 mm), torque wrench & clean shop rags (for plug well oil)Digital multimeter / noid light + compression gauge
  1. 1If motor oil is pooled inside the Cylinder 3 plug tube, vacuum/soak it dry and replace the valve cover gasket & spark plug tube seals before installing new ignition hardware.
  2. 2Replace the faulty ignition coil or spark plug verified by the swap test (replace plugs as an OEM-spec matched set if overdue).
  3. 3If P0303 stays on Cylinder 3 with verified spark, clean or replace the faulty Cylinder 3 fuel injector or repair pinched harness/PCM driver wiring.
  4. 4If Cylinder 3 compression falls > 15% below neighboring cylinders, run a cylinder leakdown test to pinpoint valve vs head-gasket vs piston-ring sealing repair.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$25 – $180
Professional Repair (Parts + Labor)$140 – $580

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Why does oil in the Cylinder 3 spark plug well trigger P0303?

Engine oil creeping past hardened valve cover tube seals softens rubber coil boots and creates a conductive carbon-track path to the cylinder head, stealing spark energy before it can jump the spark plug gap inside Cylinder 3.

Can I keep driving with code P0303?

Only cautiously to a repair bay if the CEL is solid and idle isn't violently shaking; never drive if the CEL is flashing, as unburned fuel from Cylinder 3 will rapidly overheat and destroy the catalytic converter.

Related Searches & Questions

OBD2 P0303 cylinder 3 misfire fixP0303 oil in spark plug well valve cover gasketP0303 swap coil 3 to 1 or 2 testMode 06 cylinder 3 misfire flashing CEL

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P0303: Cylinder 3 Misfire Detected — Causes, Fixes & Cost | FaultCodes.org