# OBD-II P0303: OBD-II P0303: Cylinder 3 Misfire Detected

> **Quick Answer:** Code **P0303** (SAE J2012) means the PCM's **Mode `$06` Cylinder 3 misfire counter** detected repeated combustion misfires on **Cylinder 3**. **Critical safety warning: if the Check Engine Light is FLASHING, stop driving immediately**—raw fuel dumping out of Cylinder 3 can rapidly melt the catalytic converter. Diagnose accurately before buying parts by performing the two-cylinder **component swap**: move **Cylinder 3 ignition coil -> #1 (or #2)** and move **Cylinder 3 spark plug -> a different cylinder**. Also look inside Cylinder 3's spark plug tube for **pooled motor oil from a leaking valve cover gasket**, and if the fault remains on #3 after swapping, test **fuel injector pulse/resistance** and **compression (`~120–180 psi`, within `10–15%`)** ($25–$180 DIY; $140–$580 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0303
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Ignition & Misfire System
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
On every compression/power cycle, the Crankshaft Position Sensor (`CKP`) measures rotational acceleration immediately after Cylinder 3 fires. When spark fails, fuel starves, or compression drops on #3, crankshaft speed lags momentarily and increments the **Mode `$06` Cylinder 3 misfire counter**, turning on a steady MIL (emissions level) or a **flashing MIL** (catalyst overheat threshold).

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| OBD-II Counter Channel | Mode $06 Cylinder 3 Misfire Counter | Tracks rotational deceleration specifically on Cylinder #3 firing window |
| Compression Specification | ~120–180 psi (within 10–15% spread) | Confirms valve, head gasket, and ring integrity when spark/fuel test good |
| Injector Resistance (PFI) | ~11–16 Ω + crisp noid-light pulse | Check connector power and ground switching if swap stays on #3 |
| Flashing MIL Protection Rule | Shut down engine immediately on flashing CEL | Prevents raw fuel catalyst meltdown and exhaust fire hazard |

## Commonly Affected Models & Service Bulletins
- Honda Accord / Civic / CR-V & Subaru Forester / Outback (plug-tube seal leaks & coils)
- Ford F-150 / Explorer / Escape & Jeep/Dodge/Chrysler 3.6L V6 & 2.4L Engines
- Toyota Corolla / Camry / Highlander, Nissan & VW/Audi/BMW 4- and 6-Cylinder Engines

## Common Symptoms
- Rough idling, cabin vibration, hesitation on throttle tip-in, and loss of hill-climbing power
- **Steady or flashing Check Engine Light (`P0303`)**—a flashing light requires immediate engine shutdown
- Raw gasoline smell from exhaust and sharp drop in fuel mileage

## Most Likely Root Causes
- Failed **Cylinder 3 ignition coil (COP)** or oil-soaked rubber coil boot leaking spark to ground (#1 cause)
- Engine **oil flooding the #3 spark plug well** through a hardened **valve cover / tube seal gasket**
- Worn, cracked, or fouled **Cylinder 3 spark plug** or clogged/dead **Cylinder 3 fuel injector**
- Mechanical **Cylinder 3 compression loss** (burnt valve, blown head gasket, or worn piston rings)

## Tools & Parts Reference
- OBD-II live scanner with **Mode $06** misfire count tracking
- Spark plug socket (`14 mm` / `16 mm`), torque wrench & clean shop rags (for plug well oil)
- Digital multimeter / noid light + **compression gauge**

## Step-by-Step Troubleshooting & Fix
1. If motor oil is pooled inside the Cylinder 3 plug tube, vacuum/soak it dry and replace the **valve cover gasket & spark plug tube seals** before installing new ignition hardware.
2. Replace the faulty **ignition coil** or **spark plug** verified by the swap test (replace plugs as an OEM-spec matched set if overdue).
3. If `P0303` stays on Cylinder 3 with verified spark, clean or replace the faulty **Cylinder 3 fuel injector** or repair pinched harness/PCM driver wiring.
4. If Cylinder 3 compression falls `> 15%` below neighboring cylinders, run a **cylinder leakdown test** to pinpoint valve vs head-gasket vs piston-ring sealing repair.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $25–$180 | $140–$580 |
| GBP | £20–£145 | £115–£460 |
| CAD | CA$35–CA$240 | CA$185–CA$760 |
| EUR | €25–€165 | €125–€520 |
| CHF | CHF 35–CHF 220 | CHF 180–CHF 690 |

## Frequently Asked Questions
### Why does oil in the Cylinder 3 spark plug well trigger P0303?
Engine oil creeping past hardened valve cover tube seals softens rubber coil boots and creates a conductive carbon-track path to the cylinder head, stealing spark energy before it can jump the spark plug gap inside Cylinder 3.

### Can I keep driving with code P0303?
Only cautiously to a repair bay if the CEL is solid and idle isn't violently shaking; **never drive if the CEL is flashing**, as unburned fuel from Cylinder 3 will rapidly overheat and destroy the catalytic converter.


## Verified Official & Engineering References
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [California OBD-II Misfire Monitor Rules (13 CCR § 1968.2)](https://www.law.cornell.edu/regulations/california/13-CCR-1968.2) (Official Support)
