FaultCodes.org
F.20VaillantOverheat Protection & CirculationVerified Guide· Updated: Nov 22, 2026

Vaillant Boiler Fault F.20: Safety Switch-Off via Temperature Limiter (STB)

Hardwired Safety Temperature Limiter (STB) tripped independently near ~97 °C to stop burner overheat—check cold pressure (1.0–1.5 bar) and open valves, perform one cool reset, and call a certified engineer if F.20 repeats.

Quick AnswerCritical — Stop Immediately

Vaillant code F.20 indicates a safety temperature limiter (`STB`) overheat shutdown: a dedicated hardwired thermal limit switch independent of normal NTC thermistors tripped (typically around `~97 °C` flow/primary exchanger heat) and cut power to the gas valve. Homeowner safe steps are strictly limited to checking cold boiler pressure (1.0–1.5 bar), opening shut radiator/zone valves, waiting 20 minutes to cool, and attempting one single reset. If F.20 locks out again immediately, shut down power and call a Gas Safe / certified heating engineer—continuing to reset an STB hazard risks boiling/exchanger damage, and opening the boiler requires testing circulation pump failure, heat-exchanger limescale/sludge, loose NTC harness/earth contacts, or replacing the faulty STB ($140–$560 / £95–£410).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Overheat Protection & Circulation
Professional Repair
$140 – $560

What This Fault Code Means

In Vaillant ecoTEC / atmoTEC units, electronic NTC flow and return thermistors normally modulate burner flame well before unsafe boiling. Should circulation stop completely, heavy scale trap hot pockets inside the heat exchanger, or an NTC thermistor/earth connection fall out of spec without flagging first, the hardwired STB (Sicherheits-Temperaturbegrenzer) breaks the gas-valve safety circuit physically and displays F.20.

Common Symptoms

  • Boiler shuts down abruptly with flashing F.20, losing both central heating and domestic hot water
  • Loud kettling, knocking, or steam rumbling near the heat exchanger right before shutdown
  • System trips F.20 shortly after hot water demand stops (post-heat dissipation failure) or right on firing

Most Likely Root Causes

  • Complete water circulation breakdown (failed/seized circulation pump, severe airlock, or closed isolation valves—often cascading from low pressure)
  • Heavy limescale or magnetite sludge choking primary heat exchanger passages and creating localized > 97 °C hot spots
  • Loose, water-damaged, or poor earth / harness wiring on flow/return NTC thermistors or the STB circuit
  • Tripped, fatigued, or open-circuit STB safety cutout (or flue gas safety temperature limiter on older open-flue variants)

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Safety Limiter (STB) Trip Point

Operates independently of flow/return NTC thermistors to cut gas valve

~97 °C (independent hardwired limit)
Normal Cold Static Pressure

Check gauge externally before attempting one single cool-down reset

1.0–1.5 bar
Service & Safety Boundary

Opening sealed casing, testing gas/STB, or flushing requires qualified tech

Gas Safe / Certified Engineer Only

Commonly Affected Models & Service Bulletins

  • Vaillant ecoTEC plus & ecoTEC pro Gas Condensing Boilers (VC / VCW)
  • Vaillant atmoTEC / turboTEC Wall-Hung Boilers
  • Vaillant ecoCOMPACT & auroCOMPACT Condensing Systems

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Homeowner safe check only: confirm cold system gauge reads `1.0–1.5 bar` (repressurize gently via external filling loop only if < 1.0 bar), open radiator lockshields/TRVs, allow 20 minutes cool-down, and execute one single Reset.
  2. 2Never remove the boiler front case or bypass any thermal fuse/STB cutout—if F.20 recurs even at 1.0–1.5 bar, isolate power and contact a certified Gas Safe / SHK technician.
  3. 3Certified engineer diagnosis: inspect pump rotation & capacitor/PWM control, measure flow vs return NTC curves and earth harness integrity, bleed air at automatic air vent, flush scaled plate/primary exchangers, and check STB cold continuity (~97 °C thermal rating).

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Was cold static boiler pressure below 1.0 bar or were all radiator valves turned shut?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

External filling loop & radiator bleed key (safe pressure verification only)Certified engineer: OEM Vaillant STB thermal limiter, NTC pair & multimeterCertified engineer: Flue gas analyzer, manometer & system flushing equipment
  1. 1Verify cold system gauge pressure (1.0–1.5 bar) and verify open radiator heating loop circulation paths.
  2. 2Let the boiler cool completely (~20 minutes) and try no more than one Reset press; avoid repeated restarts while hot.
  3. 3Shut off power at the spur if F.20 re-triggers and schedule a Gas Safe / certified heating engineer.
  4. 4The engineer repairs or replaces a failed circulation pump, cleans/flushes scale and sludge out of the primary heat exchanger, restores loose NTC/earth connectors, and replaces any fatigued Vaillant STB thermal limiter.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0
Professional Repair (Parts + Labor)$140 – $560

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: Vaillant F.20 (Overheat Protection & Circulation)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $140 – $560

Frequently Asked Questions

What is the difference between Vaillant F.20 and F.75?

F.75 stops the boiler before firing because the pump doesn't create a 0.05 bar pressure jump; F.20 stops it after or during firing because water overheated past the ~97 °C STB threshold—though both frequently trace back to failing circulation pumps, trapped air, or hydraulic blockages.

Can I reset Vaillant F.20 more than once to keep warm?

No—repeatedly resetting a Safety Temperature Limiter (STB) lockout can boil water trapped inside the primary heat exchanger, opening the safety relief valve or cracking heat exchanger castings. Have an engineer resolve the cause first.

Related Searches & Questions

Vaillant boiler fault F20 STB overheatVaillant ecoTEC F.20 temperature limiter resetVaillant F.20 vs F.75 circulation pumpVaillant F.20 repair cost engineer

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

HVAC & Boilers →
Vaillant Boiler Fault F.20: Safety Switch-Off via… — Fixes & Cost | FaultCodes.org