# Vaillant F.20: Vaillant Boiler Fault F.20: Safety Switch-Off via Temperature Limiter (STB)

> **Quick Answer:** Vaillant code **F.20** indicates a **safety temperature limiter (`STB`) overheat shutdown**: a dedicated hardwired thermal limit switch independent of normal NTC thermistors tripped (typically around **`~97 °C`** flow/primary exchanger heat) and cut power to the gas valve. Homeowner safe steps are strictly limited to checking cold boiler pressure (`1.0–1.5 bar`), opening shut radiator/zone valves, waiting 20 minutes to cool, and attempting **one single reset**. If `F.20` locks out again immediately, shut down power and call a **Gas Safe / certified heating engineer**—continuing to reset an STB hazard risks boiling/exchanger damage, and opening the boiler requires testing circulation pump failure, heat-exchanger limescale/sludge, loose NTC harness/earth contacts, or replacing the faulty STB ($140–$560 / £95–£410).

- **URL:** https://faultcodes.org/hvac/vaillant-f20
- **Category:** HVAC, Boilers & Heating
- **Brand / Standard:** Vaillant
- **System Area:** Overheat Protection & Circulation
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Professional Recommended
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
In Vaillant ecoTEC / atmoTEC units, electronic NTC flow and return thermistors normally modulate burner flame well before unsafe boiling. Should circulation stop completely, heavy scale trap hot pockets inside the heat exchanger, or an NTC thermistor/earth connection fall out of spec without flagging first, the **hardwired STB (Sicherheits-Temperaturbegrenzer)** breaks the gas-valve safety circuit physically and displays `F.20`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Safety Limiter (STB) Trip Point | ~97 °C (independent hardwired limit) | Operates independently of flow/return NTC thermistors to cut gas valve |
| Normal Cold Static Pressure | 1.0–1.5 bar | Check gauge externally before attempting one single cool-down reset |
| Service & Safety Boundary | Gas Safe / Certified Engineer Only | Opening sealed casing, testing gas/STB, or flushing requires qualified tech |

## Commonly Affected Models & Service Bulletins
- Vaillant ecoTEC plus & ecoTEC pro Gas Condensing Boilers (VC / VCW)
- Vaillant atmoTEC / turboTEC Wall-Hung Boilers
- Vaillant ecoCOMPACT & auroCOMPACT Condensing Systems

## Common Symptoms
- Boiler shuts down abruptly with flashing `F.20`, losing both central heating and domestic hot water
- Loud kettling, knocking, or steam rumbling near the heat exchanger right before shutdown
- System trips `F.20` shortly after hot water demand stops (post-heat dissipation failure) or right on firing

## Most Likely Root Causes
- Complete **water circulation breakdown** (failed/seized circulation pump, severe airlock, or closed isolation valves—often cascading from low pressure)
- Heavy **limescale or magnetite sludge** choking primary heat exchanger passages and creating localized `> 97 °C` hot spots
- Loose, water-damaged, or poor **earth / harness wiring** on flow/return NTC thermistors or the STB circuit
- Tripped, fatigued, or open-circuit **STB safety cutout** (or flue gas safety temperature limiter on older open-flue variants)

## Tools & Parts Reference
- External filling loop & radiator bleed key (safe pressure verification only)
- Certified engineer: OEM Vaillant STB thermal limiter, NTC pair & multimeter
- Certified engineer: Flue gas analyzer, manometer & system flushing equipment

## Step-by-Step Troubleshooting & Fix
1. Verify cold system gauge pressure (`1.0–1.5 bar`) and verify open radiator heating loop circulation paths.
2. Let the boiler cool completely (`~20 minutes`) and try **no more than one Reset press**; avoid repeated restarts while hot.
3. Shut off power at the spur if `F.20` re-triggers and schedule a **Gas Safe / certified heating engineer**.
4. The engineer repairs or replaces a failed **circulation pump**, cleans/flushes scale and sludge out of the primary heat exchanger, restores loose NTC/earth connectors, and replaces any fatigued **Vaillant STB thermal limiter**.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$0 | $140–$560 |
| GBP | £0–£0 | £95–£410 |
| CAD | CA$0–CA$0 | CA$180–CA$680 |
| EUR | €0–€0 | €120–€480 |
| CHF | CHF 0–CHF 0 | CHF 195–CHF 720 |

## Frequently Asked Questions
### What is the difference between Vaillant F.20 and F.75?
`F.75` stops the boiler *before* firing because the pump doesn't create a `0.05 bar` pressure jump; `F.20` stops it *after or during* firing because water overheated past the ~`97 °C` STB threshold—though both frequently trace back to failing circulation pumps, trapped air, or hydraulic blockages.

### Can I reset Vaillant F.20 more than once to keep warm?
No—repeatedly resetting a Safety Temperature Limiter (`STB`) lockout can boil water trapped inside the primary heat exchanger, opening the safety relief valve or cracking heat exchanger castings. Have an engineer resolve the cause first.


## Verified Official & Engineering References
- [Vaillant UK Support: Official Boiler Fault Codes (F.20)](https://www.vaillant.co.uk/homeowners/advice-and-knowledge/vaillant-boiler-fault-codes/) (Official Support)
- [Vaillant Deutschland: Störungscodes & Hilfe](https://www.vaillant.de/heizung/service/stoerungscodes/) (Official Support)
- [Vaillant UK Official Support Home](https://www.vaillant.co.uk) (Official Support)
