FaultCodes.org
F2ViessmannOverheat Protection & CirculationVerified Guide· Updated: Nov 22, 2026

Viessmann Boiler Fault F2: Overheat Safety Temperature Limiter (STB) Tripped

Burner safety lockout triggered when primary heat-exchanger flow hits ~90–100 °C and trips the hardwired Safety Temperature Limiter (STB)—check 1.0–1.5 bar pressure, radiator flow, or frozen condensate drain; do NOT force repeated resets.

Quick AnswerCritical — Stop Immediately

Fault code F2 on Viessmann Vitodens and Vitopend boilers means the Safety Temperature Limiter (STB) has tripped and locked out the burner because internal flow temperatures climbed into overheat territory (~90–100 °C depending on model limits). Safely check cold boiler gauge pressure (1.0–1.5 bar), confirm multiple radiator valves are open (not choked shut), check exterior plastic condensate lines in freezing weather, and try one single reset once cooled. Because repeated STB resets mask severe dry-firing hazards, if F2 returns immediately you must leave the casing closed and call a Gas Safe / certified heating engineer to inspect the circulation pump, sludged plate heat exchanger, airlocks, and STB sensor ($140–$540 / £100–£390).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Overheat Protection & Circulation
Professional Repair
$140 – $540

What This Fault Code Means

A Viessmann boiler relies on continuous pumped water flow to extract burner heat from the stainless/aluminum heat exchanger. Unlike soft electronic NTC faults, the STB (Safety Temperature Limiter / Sicherheits-Temperaturbegrenzer) is an independent hardwired high-limit thermal trip (~90–100 °C) that cuts power to the gas valve immediately upon trapped steam or localized boiling—resulting in lockout F2.

Common Symptoms

  • Boiler shuts down with F2 fault code, no central heating or hot water, often after kettle-like boiling noises
  • Radiators remain completely cold while boiler cabinet pipes feel scorching hot right before shutdown
  • External pressure drops erratically or pressure relief discharges if hydraulic steam expansion occurred

Most Likely Root Causes

  • Seized, failing, or severely air-locked circulation pump trapping heat inside the primary heat exchanger
  • Heavy sludge, rust, or limescale restriction choking the plate heat exchanger or flow/return loops
  • Closed system isolation valves / all radiator TRVs turned off with zero open bypass path
  • Frozen external condensate outlet backing up water (winter) or faulty high-limit STB thermostat / wiring

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Safety Temperature Limiter (STB) Trip

Hardwired high-limit thermal switch cuts gas valve directly

~90–100 °C (model-dependent)
Normal Cold Operating Pressure

Top up external loop only if pressure sits below 1.0 bar when cool

1.0–1.5 bar
Service & Casing Restriction

Do not repeatedly reset F2 or remove sealed boiler cover yourself

Certified Gas / SHK Engineer Only

Commonly Affected Models & Service Bulletins

  • Viessmann Vitodens 100-W & 200-W Gas Condensing Boilers
  • Viessmann Vitodens 050-W, 222-F & 300-W Series
  • Viessmann Vitopend 100-W Conventional Gas Boilers

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Allow the boiler 15–20 minutes to cool, check the cold pressure gauge (1.0–1.5 bar expected—top up only if under 1.0 bar), and confirm several radiators are turned wide open for heat dissipation.
  2. 2If ambient temperatures are below freezing, check exterior condensate pipes for ice plugs (safely warm externally with warm—never boiling—water only if exposed outside), then attempt one manual reset only.
  3. 3Certified engineer diagnosis (never open boiler casing yourself): check circulation pump rotation/current, bleed internal primary exchanger air, test flow/return temperature delta (ΔT), flush sludged plate exchanger, and test STB switch continuity once cooled.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Was cold boiler pressure < 1.0 bar, were all radiator valves shut, or was the exterior condensate pipe frozen solid?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

Radiator bleed key & external filling valve (safe homeowner pressure check only)Certified engineer: OEM Viessmann STB Limiter, pump test meter & pressure gaugeCertified engineer: Flue gas analyzer & power-flush / magnetic descaling equipment
  1. 1Verify cold system gauge sits at 1.0–1.5 bar, open at least 2–3 radiator valves fully, and gently bleed trapped radiator air (re-topping pressure back to 1.0–1.5 bar).
  2. 2Check visible exterior condensate pipework in sub-zero cold and thaw external ice carefully with warm—never boiling—water before pressing one single Reset after cool-down.
  3. 3Do NOT keep hitting reset if F2 returns quickly—turn the boiler off at the fused spur/control and call a Gas Safe / certified heating engineer.
  4. 4The engineer inspects and frees or replaces a jammed circulation pump, cleans magnetite/scale from the heat exchanger, verifies the diverter valve and auto air vent, or replaces a drifted high-limit STB sensor.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0
Professional Repair (Parts + Labor)$140 – $540

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: Viessmann F2 (Overheat Protection & Circulation)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $140 – $540

Frequently Asked Questions

Is Viessmann fault F2 dangerous if I keep pressing reset?

Yes—repeatedly forcing an STB overheat lockout resets the burner while water isn't circulating, risking steam flashes, pressure relief valve blowouts, or severe heat-exchanger damage. Only perform one reset after verifying cold pressure and cooling down.

What temperature triggers the Viessmann F2 STB safety cutoff?

Depending on the exact Vitodens/Vitopend platform and firmware safety margin, the hardwired STB trips once primary flow reaches roughly 90 °C to 100 °C.

Related Searches & Questions

Viessmann fault code F2 overheat STBViessmann Vitodens F2 reset fixViessmann F2 circulation pump heat exchangerViessmann boiler error F2 repair cost

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

HVAC & Boilers →
Viessmann Boiler Fault F2: Overheat Safety… — Fixes & Cost | FaultCodes.org