# Bosch / Siemens E18: Bosch / Siemens Washing Machine Drain Error E18 (F18 / d02)

> **Quick Answer:** Bosch / Siemens washing machine error `E18` (also displayed as `F18` or `d02` on select series) means the washer timed out trying to pump out water. Turn the dial to Off, **unplug the washer**, and **let hot wash water cool down before draining** to prevent scalding. Per official Bosch Support guidelines, empty standing water via the small bottom-front emergency drain hose into a shallow baking tray, unscrew and clean the coin-trap pump filter, verify the pump impeller blades inside turn freely, check the rear hose for kinks or unremoved sink-spigot plugs, then test for leaks by pouring **1 liter (1 quart)** of water into the detergent drawer and running **Drain/Spin** ($0–$65 DIY; $120–$260 technician).

- **URL:** https://faultcodes.org/appliances/bosch-e18
- **Category:** Home Appliances
- **Brand / Standard:** Bosch / Siemens
- **System Area:** Drain Pump & Filter
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Before high-speed spinning begins, the BSH water-level pressure sensor must register an empty tub within the allotted pump cycle time. When coins, hairpins, lint, or detergent buildup block the filter—or the drain hose kinks behind the washer or connects to an obstructed wall/sink trap—the machine halts with `E18` and locks the door to keep dirty water off your floor.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Equivalent Display Codes | E18 / F18 / d02 (BSH Drain Timeout) | Code format varies across Serie 4 / 6 / 8 & iQ300 / iQ500 displays |
| Hot-Water Safety Rule | Turn dial Off, unplug & let cool first | Prevents scald injury from 60–90 °C wash water before opening drain hose |
| Official Post-Clean Test | Pour 1 L (1 qt) in drawer -> Drain/Spin | Verifies filter gasket seal and full pump evacuation (Bosch Support) |
| Common Installation Trap | Closed blanking plug in sink siphon spigot | Frequent cause of E18 on newly plumbed washers |

## Commonly Affected Models & Service Bulletins
- Bosch Front-Load Washers (Serie 4, Serie 6, Serie 8, WAN / WAT / WAX / WAU)
- Siemens Front-Load Washers (iQ300, iQ500, iQ700, WM-series sharing `F18`/`E18` error codes)
- Neff & Constructa BSH-built front-loading washing machines

## Common Symptoms
- Washer pauses mid-cycle before rinsing or spinning with water trapped behind the glass door
- Display shows `E18` (or `F18`/`d02`) with dull pump humming and zero drainage
- Washer door stays safety-locked while water covers the bottom door gasket

## Most Likely Root Causes
- Clogged bottom-front **drain pump filter / coin trap** packed with lint, coins, buttons, or small socks (#1 cause)
- Hairpin, bra wire, or glass sliver wedged behind the filter inside the **pump impeller blades**
- Kinked or crushed rear black drain hose, or an **unremoved knockout plug** inside a newly fitted sink-siphon spigot
- Clogged pressure chamber hose or electrically burned-out BSH drain pump motor

## Tools & Parts Reference
- Shallow baking pan / low tray & thick towels
- Flashlight (to inspect pump impeller cavity)
- 1-liter measuring jug / bottle (for official Drain/Spin seal test)
- Soft brush (to clean filter threads & rubber gasket)

## Step-by-Step Troubleshooting & Fix
1. Turn program knob to Off, unplug the appliance, and let high-temperature wash water cool below scalding risk.
2. Open the bottom-right (or left) service flap, pull the small emergency drain hose forward over a shallow baking dish, pull its cap out to empty the drum slowly, then push the cap firmly back in.
3. Unscrew the circular pump filter counter-clockwise, rinse under warm water, clean the threads + rubber seal ring, ensure the internal impeller wheel rotates freely, and tighten the filter cap firmly clockwise.
4. Inspect the rear black corrugated drain hose for kinks and verify no knockout plug remains inside an under-sink spigot, then pour **1 liter (1 quart)** into the dispenser drawer and run **Drain/Spin** to confirm zero leaks and smooth draining.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$65 | $120–$260 |
| GBP | £0–£52 | £95–£200 |
| CAD | CA$0–CA$85 | CA$160–CA$340 |
| EUR | €0–€60 | €110–€235 |
| CHF | CHF 0–CHF 75 | CHF 150–CHF 310 |

## Frequently Asked Questions
### Why does Bosch tell you to pour 1 liter of water into the drawer after cleaning the E18 filter?
Pouring ~1 liter (1 quart) into the dispenser drawer wets the internal eco-ball seal and lets you verify right away during **Drain/Spin** both that the filter rubber gasket doesn't drip on the floor and that the pump clears water cleanly.

### How do I open the door when my Bosch washer stops full of water with E18?
Never force the handle! Unplug the machine, let hot water cool, and drain the entire drum slowly through the small emergency hose behind the bottom service panel—once water level drops completely, wait 2–3 minutes for the thermal door lock to release.


## Verified Official & Engineering References
- [Bosch Official Support: E18 / F18 Drain Error Guide](https://www.bosch-home.com/us/owner-support/get-support/owner-manuals) (Official Support)
- [Bosch Official Spare Parts & Pump Lookup (E-Nr)](https://www.bosch-home.com/us/shop) (Technical Manual)
