# Samsung 4E: Samsung Washing Machine Water Supply Error (4E / 4C)

> **Quick Answer:** Samsung washer error `4E` (displayed as **`4C`** on newer EcoBubble/Smart Care models) means insufficient water entered the drum within the fill timer. Turn the taps off cleanly before inspecting, verify **both hot and cold water supply taps are turned fully open** (even on cold cycles on dual-inlet units), straighten pinched rear hoses, scrub sand/scale from the **inlet valve mesh screens** (Samsung recommends cleaning every 6 months), clear detergent dispenser sludge, and remove any aftermarket **'Flood Safe'** auto-shutoff hoses—Samsung warns those trigger false `4E`/`4C` faults ($0–$75 DIY mesh clean/valve; $120–$250 technician).

- **URL:** https://faultcodes.org/appliances/samsung-4e
- **Category:** Home Appliances
- **Brand / Standard:** Samsung
- **System Area:** Water Inlet Valve & Supply
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
When starting a wash or rinse fill, Samsung's control PCB energizes the dual cold/hot solenoid inlet valves and expects the pressure level switch to climb steadily within ~10–15 minutes. If sediment plugs the tiny stainless mesh filters inside the hose ports, a valve coil opens, or water flow trips slow, the washer locks with `4E` / `4C`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Model Display Equivalents | 4E (Classic) / 4C (Newer EcoBubble) | Identical water-fill timeout error across model years |
| Mesh Screen Maintenance Interval | Clean twice per year (every 6 months) | Located inside both rear inlet ports and hose coupler ends |
| Samsung Hose Warning | Avoid third-party 'Flood Safe' hoses | Internal shutoff valves trip falsely under initial fill rush (Samsung Support) |
| Electrical Inlet Valve Spec | 120V / 230V AC supply during fill stage | Verify coil resistance (~800–1,200 Ω) or active fill voltage when dry |

## Commonly Affected Models & Service Bulletins
- Samsung EcoBubble & AddWash Front-Load Washers (WW60 / WW70 / WW80 / WW90 / WF45 series)
- Samsung Top-Load High-Efficiency Washers (WA45 / WA50 / WA52 series)
- Samsung Smart Care Washer-Dryer Combos showing `4C` or `4E`

## Common Symptoms
- Washer flashes `4E` or `4C` minutes after starting a wash or right before rinse fill
- Dry laundry inside the drum with barely any water pooling at the bottom, or very loud humming from the back valves
- Water dribbles slowly through the detergent dispenser tray

## Most Likely Root Causes
- Partially closed water supply faucet (or **both hot & cold taps** not turned open on dual-inlet North American/global units) or pinched rear inlet hose
- Rust, sand, or calcium scale clogging the **inlet mesh screens** inside the rear valve ports (or hose ends)
- Third-party **'Flood Safe'** burst-protection hoses falsely shutting flow off (explicitly flagged by Samsung Support)
- Clogged detergent dispenser drawer ports or electrically failed **water inlet solenoid valve** / disconnected pressure sensor hose

## Tools & Parts Reference
- Needle-nose pliers (to extract mesh screens gently)
- Soft toothbrush (for calcium/rust cleaning)
- Bucket & towels (before disconnecting water hoses)
- Multimeter & OEM Water Inlet Valve (if solenoid coils fail)

## Step-by-Step Troubleshooting & Fix
1. Open both cold and hot supply taps completely and replace any aftermarket 'Flood Safe' hoses with standard braided stainless-steel supply hoses.
2. Turn taps off, disconnect hoses from the rear water ports, gently pull out the mesh filters with needle-nose pliers, brush completely clean under running water with a toothbrush, re-seat filters firmly, and leak-test connections slowly.
3. Pull the detergent dispenser drawer all the way out, scrub hardened soap/fabric softener out of its top spray nozzles and siphon tubes under warm water.
4. If pressure is strong and mesh filters are spotless yet water barely enters while voltage reaches the inlet valve coils (`120V/230V AC`), unplug power and replace the OEM **Water Inlet Valve Assembly**.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$75 | $120–$250 |
| GBP | £0–£60 | £95–£195 |
| CAD | CA$0–CA$95 | CA$155–CA$325 |
| EUR | €0–€68 | €110–€225 |
| CHF | CHF 0–CHF 85 | CHF 145–CHF 295 |

## Frequently Asked Questions
### What is the difference between 4E and 4C on Samsung washers?
They are the exact same water-supply fault code—older Samsung washers display **`4E`**, while newer EcoBubble and Smart Care models display **`4C`**.

### How often does Samsung recommend cleaning inlet mesh filters?
Samsung Support recommends shutting off the water taps and brushing both inlet mesh screens clean **at least twice a year**, especially in areas with hard water or municipal pipe sediment.


## Verified Official & Engineering References
- [Samsung Official Support: 4E / 4C Water Supply Troubleshooting](https://www.samsung.com/us/support/troubleshooting/) (Official Support)
- [Samsung Support Portal & Manuals](https://www.samsung.com/us/support/) (Technical Manual)
