# Bosch / Siemens E09: Bosch / Siemens Dishwasher E09: Circulation Heat Pump Heater Failure

> **Quick Answer:** Code **E09** (or `E:09` / `F09`) on Bosch, Siemens, Neff, and Gaggenau dishwashers indicates a **water heating circuit fault**. On BSH dishwashers built since the late 2000s, the flow-through heater is molded inside the **circulation heat pump assembly** rather than sold as a standalone tubular element. Test the disconnected pump heater terminals with a multimeter: healthy elements measure **~20–25 Ω** (most commonly `20–22 Ω`, or `~11 Ω` per section on older dual-circuit variants) with infinite (`OL`) insulation to ground; `OL` across the heater pins confirms a burned heating trace requiring heat-pump replacement matched to the exact door-frame **E-Nr** nameplate ($85–$150 DIY; $220–$390 technician).

- **URL:** https://faultcodes.org/appliances/bosch-e09
- **Category:** Home Appliances
- **Brand / Standard:** Bosch / Siemens
- **System Area:** Dishwasher Heating Pump
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
During heated wash and final rinse stages, the main power module closes a relay feeding AC power to thick-film heating tracks wrapped around the stainless circulation pump cylinder, monitoring temperature via NTC thermistors. When calcification or dry thermal cycling fractures the heating trace (`OL`) or burns the control board relay/connector, water stays cold and the controller aborts at cycle end with `E09`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Integrated Heater Nominal Resistance | 20–25 Ω (typically ~20–22 Ω) | Older dual-circuit BSH variants read ~11 Ω per coil section |
| Fault / Burnout Reading | OL / ∞ Ω (open circuit) | Most frequent cause of E09; indicates fractured thick-film track |
| Chassis Ground Insulation Check | OL / ∞ Ω (to pump metal body) | Any continuity to ground leaks current and trips RCD/breaker |
| OEM Part Lookup Identifier | Exact Door-Frame E-Nr + FD | Pump connector orientation & hose diameter vary by BSH series |

## Commonly Affected Models & Service Bulletins
- Bosch Serie 4 / Serie 6 / Serie 8 Dishwashers (SMV / SMS / SMI / SHX Series)
- Siemens iQ300 / iQ500 / iQ700 Dishwashers (SN / SX Series)
- Neff, Constructa & Gaggenau BSH-Platform Flow-Through Heat Pump Dishwashers

## Common Symptoms
- Dishwasher finishes its cycle (or stops late) leaving dishes wet, greasy, and cold with `E09` displayed
- Detergent pod remains partially undissolved in the dispenser or sump because wash water never heated
- Tripped household breaker/RCD alongside `E09` if the heater element insulation shorted to the metal housing

## Most Likely Root Causes
- Burned-out thick-film heating element integrated inside the **BSH circulation heat pump** (open circuit `OL`, ~85% of cases)
- Burnt or cold-soldered **heater relay / melted terminal pins** on the main power control module
- Overheated or scorched red power harness plug feeding the heat pump heater connector
- Ground fault / insulation breakdown inside the flow-through pump heater jacket

## Tools & Parts Reference
- Digital multimeter (Ω resistance + continuity-to-ground check)
- Torx T20 screwdriver (kickplate & right side panel removal)
- OEM BSH Circulation Heat Pump matched by E-Nr + stainless hose clamp
- Pliers / towels to catch residual sump water

## Step-by-Step Troubleshooting & Fix
1. Disconnect mains power and turn off the under-sink water valve before tilting or opening the right-hand side panel.
2. Check the heater connector and wiring harness back to the lower-right control module for heat discoloration or loose crimp pins; measure across heater pins (`20–25 Ω` normal; `OL` = failed heater trace).
3. If the heater reads `OL` or shorts to ground, release the sump rubber clamp and install an exact-match **OEM BSH circulation heat pump** ordered by full **E-Nr** (fit new single-use ear/screw hose clamps so the sump cannot leak and trip `E15`).
4. If the pump heater reads cleanly at `20–22 Ω` with no ground fault, inspect the lower power PCB for a burnt solder joint or failed heater relay and test heated wash water temperature on a quick hot program.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $85–$150 | $220–$390 |
| GBP | £70–£125 | £180–£320 |
| CAD | CA$110–CA$195 | CA$280–CA$490 |
| EUR | €75–€135 | €195–€350 |
| CHF | CHF 95–CHF 170 | CHF 260–CHF 460 |

## Frequently Asked Questions
### Can I replace just the heating element instead of the whole Bosch heat pump?
On standard BSH Zeolith/flow-through circulation pumps, official Bosch/Siemens service supplies the sealed heater and pump housing as one complete assembly. Ensure your replacement kit includes a stainless worm-drive or Oetiker clamp matched to the exact E-Nr.

### Is it safe to run the dishwasher when E09 appears?
No. Wash water stays cold, detergent won't rinse or sanitize properly, and if an internal heater insulation fault is present it can repeatedly trip your breaker/RCD.


## Verified Official & Engineering References
- [Bosch Home Service: Dishwasher Error Code Help](https://www.bosch-home.com/us/service) (Official Support)
- [Siemens Kundendienst: Geschirrspüler Fehler E09](https://www.siemens-home.bsh-group.com/de/kundenservice) (Official Support)
- [Bosch Home UK Customer Service](https://www.bosch-home.co.uk/customer-service) (Official Support)
