# Bosch / Siemens E24: Bosch / Siemens Dishwasher E24: Drain Hose, Siphon or Pump Cover Blocked

> **Quick Answer:** Code **E24** on Bosch, Siemens, Neff, and Gaggenau dishwashers signals a **drainage flow restriction** (closely related to **E25** jammed impeller). After switching off power and removing lower sump standing water, check three places: verify the **sink siphon / garbage disposal knockout plug** was removed and isn't clogged with grease, straighten any kinked corrugated drain hose behind the unit, and clean the triple filter plus click the white **drain pump cover** tightly into place until it snaps—a loose cover drops suction and immediately re-triggers `E24`. Clearing a pump cover, hose, or siphon costs $0; replacing a failed drain pump runs ~$35–$75 DIY ($120–$260 technician).

- **URL:** https://faultcodes.org/appliances/bosch-e24
- **Category:** Home Appliances
- **Brand / Standard:** Bosch / Siemens
- **System Area:** Dishwasher Drain Hose
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Before refilling or ending cycles, BSH dishwashers sense drain load through current draw on the heat/circulation pump and drain pump. If backpressure from a clogged sink spigot, pinched rear hose, garbage-disposal plug on new installs, or air bypass around an unlatched sump **pump cover** slows evacuation, the PCB halts with `E24` within minutes.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Sump Pump Cover Requirement | Audible snap-lock seal | Loose volute cover prevents pressure buildup and causes immediate E24 |
| Program Drain Reset Hold | Reset / Cancel held 3 s (`0:01`) | Forces 1-minute pump-out test after sump/siphon service |
| Companion Impeller Jam Code | E25 (blocked impeller / missing cover) | Both E24 & E25 share pump cavity, check valve, and siphon troubleshooting |

## Commonly Affected Models & Service Bulletins
- Bosch Serie 2 / Serie 4 / Serie 6 / Serie 8 Dishwashers (SMS / SMV / SMI / SHE / SHX)
- Siemens iQ100 / iQ300 / iQ500 / iQ700 Dishwashers (SN / SX Series)
- Neff & Gaggenau BSH-Group Dishwashers

## Common Symptoms
- Dishwasher stops early or near cycle end displaying `E24` with murky standing water in the bottom sump
- Draining sound runs sluggishly or makes a sucking noise because the pump cover isn't snapped down flush
- `E24` appears immediately on the very first run of a newly installed dishwasher

## Most Likely Root Causes
- Loose or unlatched white **drain pump cover** inside the sump letting pump pressure bypass cleanly
- Clogged under-sink **siphon spigot** (grease plug) or unremoved **garbage disposal knockout plug** on fresh installations
- Pinched, sharply bent, or collapsed corrugated **drain hose** behind the cabinet
- Debris (`E25` overlap: glass chips, olive/lemon seeds, labels) blocking pump impeller or failing drain pump motor

## Tools & Parts Reference
- Cut-resistant gloves & sponge/towels (safe sump glass/water removal)
- Flathead screwdriver / nut driver (hose clamp & sink siphon cleaning)
- Multimeter (only needed if testing pump windings after plumbing clears)

## Step-by-Step Troubleshooting & Fix
1. Turn off mains power, wear gloves (in case glass fragments rest in the sump), clean the cylinder/flat mesh filters, lift off the drain pump cover, spin out any pits/shards blocking the impeller, and lock the pump cover securely until it clicks.
2. Straighten kinks along the corrugated drain hose behind the dishwasher and pull off its clamped connection at the sink **siphon / disposal inlet**.
3. Poke out grease buildup inside the sink trap branch—or knock out and retrieve the solid plastic **disposal inlet plug** if recently installed—then clamp the drain hose firmly onto the spigot.
4. Restore power, hold **Reset / Cancel (3 s)** until `0:01` drains any remaining sump water, and verify a Quick Wash completes with zero `E24` alert (replace the drain pump only if impeller path and plumbing are spotless yet pump won't spin).

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$75 | $120–$260 |
| GBP | £0–£60 | £90–£200 |
| CAD | CA$0–CA$95 | CA$150–CA$320 |
| EUR | €0–€65 | €100–€220 |
| CHF | CHF 0–CHF 85 | CHF 150–CHF 310 |

## Frequently Asked Questions
### Why does an unlocked drain pump cover trigger Bosch E24 even when everything is clean?
BSH specifies that the snap-in pump cover forms the volute seal over the impeller. If left slightly tilted or unclicked after cleaning the filter, water simply swirls inside the sump instead of building head pressure up the drain hose, tripping `E24`.

### How do I reset Bosch error E24 once the clog is cleared?
Press and hold the **Reset / Start (3 sec)** button until the display changes to `0:01`, close the door so the 1-minute drain cycle completes, then restart your program.


## Verified Official & Engineering References
- [Bosch Home Service: Dishwasher E24 Drainage Guide](https://www.bosch-home.com/us/service) (Official Support)
- [Siemens Kundendienst: Geschirrspüler Fehler E24 / E25](https://www.siemens-home.bsh-group.com/de/kundenservice) (Official Support)
- [Bosch Home UK Customer Support](https://www.bosch-home.co.uk/customer-service) (Official Support)
