# Miele F11: Miele Dishwasher Water Drainage Error (F11)

> **Quick Answer:** Miele dishwasher error `F11` signals a **water drainage fault**. Unplug/shut off the breaker and ladle out standing sump water before reaching inside—hidden glass shards often sit around the pump wheel. According to **official Miele Support steps**, clean the triple-filter assembly first, release the **non-return check valve** by pressing its catch inward and tilting inward to lift it out, manually rotate the **drain pump impeller** beneath it to clear seeds/glass, and critically **seat the non-return valve vertically from above until it clicks completely straight** (a crooked non-return valve is one of the top reasons `F11` keeps coming back) ($0–$95 DIY check/valve; $140–$290 Miele service).

- **URL:** https://faultcodes.org/appliances/miele-f11
- **Category:** Home Appliances
- **Brand / Standard:** Miele
- **System Area:** Drainage System
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
At the end of pre-rinse and main wash stages, Miele's drain pump pushes water past a spring-hinged ball non-return valve up the discharge hose. If food grease glues the triple filter shut, a lemon seed/glass shard jams the uncovered impeller beneath the check valve, or someone snaps the check valve back slightly sideways so water backflows, `F11` interrupts the wash.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Non-Return Valve Release Step | Press catch inward -> tilt inward & lift | Located inside dishwasher sump beneath the triple-filter combo |
| Official Re-Installation Alignment | Place vertically straight from above until click | A cocked non-return valve is a top cause of recurring F11 faults |
| Impeller Test Feel (Power OFF) | Spins smoothly with gentle magnetic steps | Hard stops indicate trapped glass, bones, or toothpicks (use gloves) |
| Filter Combo Structure | 3-stage (coarse + micro + flat fine filter) | All 3 stages must lock tightly flush onto the sump floor |

## Commonly Affected Models & Service Bulletins
- Miele G4000 & G5000 Series Dishwashers
- Miele G6000 & G7000 AutoDos EcoFlex Dishwashers
- Miele Integrated & Freestanding Dishwashers with removable sump Non-Return Valve

## Common Symptoms
- Dishwasher stops with standing water covering the bottom stainless sump filter grid and beeps `F11`
- Gurgling/humming noise near the sump without water moving through the sink trap
- Repeated `F11` directly after cleaning filters if the non-return valve was seated unevenly

## Most Likely Root Causes
- Grease-caked **triple-filter combination** (coarse filter, micro-filter, and flat fine filter) choking water return
- Jammed, warped, or **improperly seated non-return (check) valve** beneath the filter grid
- Broken glass shard, cherry pit, toothpick, or bone sliver blocking the **drain pump impeller blades** under the non-return valve
- Kinked rear drain hose, blocked sink spigot/disposal knockout plug, or burned-out Miele drain pump

## Tools & Parts Reference
- Cut-resistant gloves (for safely checking glass chips in sump)
- Cup / sponge & towels to bale standing water
- Soft brush & warm soapy water (triple-filter & check valve cleaning)
- Replacement OEM Miele non-return valve (if rubber flap warped/torn)

## Step-by-Step Troubleshooting & Fix
1. Disconnect electrical power and scoop out standing sump water with a cup/sponge.
2. Remove and wash the triple-filter assembly (coarse, cylindrical micro, and flat fine screen) in hot soapy water.
3. Release the **non-return check valve** (press locking catch inward -> tilt inward), wash it clean, carefully clear glass chips/pits from the exposed **drain pump impeller blades** underneath, and confirm smooth rotation.
4. **Crucial Official Re-Install:** Lower the non-return valve **strictly vertically from straight above** until it clicks firmly flat—test that it isn't cocked crooked, re-fit the triple filter tightly, inspect the external sink trap/drain hose for kinks, and test a short Rinse cycle.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$95 | $140–$290 |
| GBP | £0–£75 | £110–£230 |
| CAD | CA$0–CA$125 | CA$185–CA$375 |
| EUR | €0–€85 | €125–€260 |
| CHF | CHF 0–CHF 105 | CHF 165–CHF 340 |

## Frequently Asked Questions
### Why does Miele F11 often come back right after someone cleans the filter?
Miele warns that the **non-return valve** must be lowered **vertically from straight above** until it clicks flush. Setting it in sideways leaves a gap or jams the internal check ball, triggering immediate `F11` drainage failures.

### Can I feel the drain pump impeller move cleanly by hand?
Yes—after disconnecting power and guarding fingers against glass splinters, spinning the impeller beneath the check valve should feel smooth with gentle magnetic motor detents (`step-step-step`), never gritty or locked solid.


## Verified Official & Engineering References
- [Miele Customer Assistance: F11 Drainage Error Steps](https://www.miele.co.uk/support/customer-assistance) (Official Support)
- [Miele Dishwasher Instruction Manuals & Sump Maintenance](https://www.miele.co.uk/c/manuals-125.htm) (Technical Manual)
