# Vaillant F.28: Vaillant Boiler Fault Code F.28: Ignition Failure Lockout

> **Quick Answer:** Vaillant fault code `F.28` (or `F28`) means the boiler triggered **3 consecutive ignition attempts** without detecting a micro-amp flame ionization signal and locked out safely to prevent unburnt gas buildup. Safely verify that other gas appliances work (plus check prepayment meter credit if applicable), inspect exterior plastic condensate pipes for winter freezing (thaw gently with **warm, never boiling water**), ensure the outdoor flue terminal isn't blocked, and press **Reset once only**. If `F.28` returns—or if you ever smell gas—**do not press Reset repeatedly and do not open the boiler casing**; book a certified Gas Safe / HVAC engineer (€0 safe homeowner checks; $140–$560 / £95–£420 professional repair).

- **URL:** https://faultcodes.org/hvac/vaillant-f28
- **Category:** HVAC, Boilers & Heating
- **Brand / Standard:** Vaillant
- **System Area:** Gas Ignition & Flame Sensing
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Professional Recommended
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
On heat or hot-water demand, the Vaillant PCB opens the gas control valve, triggers the ignition transformer spark across the electrode gap, and measures ionization rectification micro-amps (`µA`). If zero flame signal returns across three start cycles, `F.28` locks the burner off safely.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Boiler Ignition Retry Lockout | 3 consecutive failed ignition attempts | Locks out safely when zero ionization flame current registers |
| Flame Detection Principle | Ionization electrode micro-amp (µA) signal | Carbon buildup or cracked electrode ceramic breaks flame sensing |
| Safe Homeowner Reset Limit | Max 1 single reset check | Repeated resets without resolving cause risk unburnt gas buildup |
| Common Cold-Weather Cause | Frozen external condensate pipe (<0 °C) | Thaw safely outside using warm (never boiling) water |

## Commonly Affected Models & Service Bulletins
- Vaillant ecoTEC plus & ecoTEC pro Wall-Hung Condensing Gas Boilers
- Vaillant ecoTEC exclusive & ecoCOMPACT Combi/System Units
- Vaillant atmoTEC / turboTEC Gas Heating Boilers

## Common Symptoms
- Display shows flashing `F.28` / `F28` with crossed-out flame icon and zero heating or hot water
- Clicking ignition sparks or three fan start/stop attempts followed by lockout
- Commonly appears during freezing winter snaps (frozen outdoor condensate line) or after street/meter gas shutoffs

## Most Likely Root Causes
- Interrupted gas supply, closed boiler yellow gas cock, empty prepayment gas meter, or air pocket in pipe after nearby gas maintenance
- Frozen external plastic condensate drain pipe causing condensate water to back up inside the combustion chamber
- Pitted, cracked, or carbon-fouled ignition / ionization electrode or frayed high-voltage ignition lead
- Restricted air intake / flue terminal recirculation, seized/defective gas valve solenoid, low dynamic gas pressure, or PCB failure

## Tools & Parts Reference
- Warm (non-boiling) water bottle or jug (external condensate pipe thawing only)
- Certified engineer calibrated gas manometer (standing & working mbar/kPa)
- Certified engineer combustion gas analyzer & OEM Vaillant electrode set

## Step-by-Step Troubleshooting & Fix
1. Confirm active household gas supply (check other gas appliances, emergency shutoff, and prepayment credit).
2. If sub-zero weather froze an exterior plastic condensate pipe, gently pour **warm (never boiling)** water along the pipe or hold a hot-water bottle against the frozen elbow to thaw it cleanly.
3. Press the Vaillant crossed-flame Reset button **once** cleanly and listen for normal ignition.
4. If `F.28` locks out again immediately: **stop pressing Reset** and call a certified gas heating engineer to inspect/clean or replace worn ignition & ionization electrodes, verify ignition cable insulation, measure dynamic standing & working gas pressures, test gas valve solenoids, and check PCB outputs.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$0 | $140–$560 |
| GBP | £0–£0 | £95–£420 |
| CAD | CA$0–CA$0 | CA$180–CA$680 |
| EUR | €0–€0 | €120–€460 |
| CHF | CHF 0–CHF 0 | CHF 190–CHF 690 |

## Frequently Asked Questions
### How many times is it safe to press Reset for Vaillant F.28?
Vaillant and Gas Safe engineers advise resetting **at most once** after confirming gas supply and thawing any frozen condensate pipe—repeated resets can accumulate unburnt gas or mask unsafe flue/valve faults.

### What is the difference between Vaillant F.28 and F.29?
`F.28` fails to establish a flame during **initial ignition start-up** (3 failed attempts), whereas `F.29` ignites cleanly first and then loses its flame **during active running**.


## Verified Official & Engineering References
- [Vaillant Official Boiler Fault Codes (F.28 Guide)](https://www.vaillant.co.uk/homeowners/advice-and-knowledge/vaillant-boiler-fault-codes/) (Official Support)
- [Vaillant Homeowner Advice & Troubleshooting Hub](https://www.vaillant.co.uk/homeowners/advice-and-knowledge/) (Technical Manual)
