FaultCodes.org
P0106OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0106 Fault Code: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance

OBD-II P0106 (Fuel Trim & Air/O2 Metering): Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance.

Quick AnswerHigh — Service Soon

OBD-II fault code P0106 indicates Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$324.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $324

What This Fault Code Means

The manifold absolute pressure (MAP) sensor measures the pressure behind the throttle; on vehicles without a separate barometric sensor it also supplies the ambient pressure, read at key-on or wide-open throttle – hence 'MAP/BARO'. It is a three-wire sensor with 5 V reference, ground and signal. P0106 is a plausibility fault: the signal is electrically valid but implausible – stuck, offset or drifting. Two tests are common. With the engine stopped, all pressures equalise, so MAP must match ambient (and boost) pressure; Ford allows 1.5–3 inHg. While running, MAP is compared with a value modelled from air mass, throttle and speed – GM blames the MAP sensor above about 23–30 kPa error, with two trips on petrol and one on diesel. Turbo engines with three sensors find the odd one out by majority. Besides the sensor, intake or boost leaks often cause it.

Common Symptoms

  • Check engine light on
  • Rough idle, hesitation, poor response
  • Higher consumption, black smoke possible on diesels
  • Loss of power or limp mode on turbo engines

Most Likely Root Causes

  • Vacuum leak at the intake manifold or boost leak (hose, clamp, charge air cooler)
  • Sensor oiled or sooted, port blocked (EGR soot), characteristic drifted
  • High resistance in signal, reference or ground wire
  • Comparison sensor wrong, or mechanical cause (dirty throttle, EGR stuck open)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0106.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Manifold Absolute Pressure Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0106?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Manifold Absolute Pressure Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Manifold Absolute Pressure Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0106 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $136
Professional Repair (Parts + Labor)$43 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P0106?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0106?

DIY replacement parts average $16–$136, while professional service averages $43–$324.

Will resetting P0106 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0106 fault code meaningP0106 repair costhow to fix P0106

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0106 Fault Code: Manifold Absolute… — Fixes & Cost | FaultCodes.org