FaultCodes.org
P010COBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P010C Fault Code: Mass or Volume Air Flow Sensor B Circuit Low

OBD-II P010C (Fuel Trim & Air/O2 Metering): Mass or Volume Air Flow Sensor B Circuit Low.

Quick AnswerHigh — Service Soon

OBD-II fault code P010C indicates Mass or Volume Air Flow Sensor B Circuit Low. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$378.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $378

What This Fault Code Means

Sensor B is a second mass air flow sensor in a second intake path, found on engines with two air filter boxes – for example the Nissan VR30DDTT twin-turbo V6 (where sensor B belongs to bank 2) or GM's 3.0 litre twin-turbo V6. P010C means the signal of sensor B is below its electrical lower limit – the counterpart of P0102. GM's twin-turbo V6 sets it at 400 Hz or less (300 failed out of 375 samples, two trips); Ford's digital sensor B below 1.5 kHz for 5 s. The usual causes are an open or grounded signal wire, a corroded connector, missing supply or failed sensor electronics. The engine continues with a calculated substitute value.

Common Symptoms

  • Check engine light on
  • Lack of power, substitute value mode
  • Rough idle, hesitation

Most Likely Root Causes

  • Signal wire of sensor B open or grounded, connector corroded
  • Sensor B electronics failed
  • Supply or ground of sensor B faulty
  • Control module input faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P010C.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Mass Air Flow Sensor B.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P010C?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Mass Air Flow Sensor B.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Mass Air Flow Sensor B.
  5. 5Clear fault memory and run a verification cycle to confirm P010C does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $159
Professional Repair (Parts + Labor)$43 – $378

Frequently Asked Questions

Is it safe to keep operating with fault code P010C?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P010C?

DIY replacement parts average $16–$159, while professional service averages $43–$378.

Will resetting P010C fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P010C fault code meaningP010C repair costhow to fix P010C

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P010C Fault Code: Mass or Volume Air Flow Sensor B Circuit Low | FaultCodes.org