FaultCodes.org
P0137OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0137 Fault Code: O2 Sensor Circuit Low Voltage Bank 1 Sensor 2

OBD-II P0137 (Fuel Trim & Air/O2 Metering): O2 Sensor Circuit Low Voltage Bank 1 Sensor 2.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0137 indicates O2 Sensor Circuit Low Voltage Bank 1 Sensor 2. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$65 – $270

What This Fault Code Means

The oxygen sensor after the catalytic converter on bank 1 (sensor 2) is a switching sensor (about 0.1–0.9 V) used for converter monitoring and fine mixture trim. P0137 means the signal stays below the lower limit. Documented limits: GM below 40–60 mV (two trips); Ford switches in a pull-up and reads open above 1 MΩ (20 kΩ from 2020) or short to ground below 10 Ω, within 10 s. Subaru uses the code as a functional test instead: the sensor never reaches 550 mV within 200 s after fuel cut-off, i.e. it behaves as if permanently lean – so a real exhaust leak can also trigger it there. When it fails, the control module stops the downstream trim and cannot evaluate the converter; there is no limp mode.

Common Symptoms

  • Check engine light on (usually after two drive cycles)
  • Catalyst monitor readiness not set
  • Usually no noticeable change in driving

Most Likely Root Causes

  • Signal wire shorted to ground or melted against the exhaust
  • Sensor faulty (cracked element, thermal shock from water)
  • Signal circuit open (counts as low on Ford)
  • Exhaust leak ahead of the sensor (lean reading)
  • Signal and ground wires swapped after a repair

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0137.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank1 Sensor2.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0137?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank1 Sensor2.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank1 Sensor2.
  5. 5Clear fault memory and run a verification cycle to confirm P0137 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $113
Professional Repair (Parts + Labor)$65 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0137?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0137?

DIY replacement parts average $23–$113, while professional service averages $65–$270.

Will resetting P0137 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0137 fault code meaningP0137 repair costhow to fix P0137

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0137 Fault Code: O2 Sensor Circuit Low Voltage Bank 1 Sensor 2 | FaultCodes.org