FaultCodes.org
P0146OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0146 Fault Code: O2 Sensor Circuit No Activity Detected Bank 1 Sensor 3

OBD-II P0146 (Fuel Trim & Air/O2 Metering): O2 Sensor Circuit No Activity Detected Bank 1 Sensor 3.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0146 indicates O2 Sensor Circuit No Activity Detected Bank 1 Sensor 3. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$54 – $270

What This Fault Code Means

Sensor 3 is a third oxygen sensor on bank 1, behind a second converter or converter brick. It only exists on some vehicles – documented for Jaguar Land Rover's 3.0 V6 supercharged (2013–2016, where sensor 2 is 'mid-cat' and sensor 3 'post-cat') and Ford systems that monitor part of the converter volume. P0146 means sensor 3 produces no voltage of its own and only the control module's bias voltage is seen, as for sensor 2 (P0140): GM evaluates a signal stuck in the 401–548 mV band, a high internal resistance or, with 1900 mV bias, an open circuit. No manufacturer document using exactly this code was found; Jaguar Land Rover lists only P0142–P0144 and P0147 for its sensor 3. When it fails, the control module stops the downstream trim and cannot evaluate the converter; there is no limp mode.

Common Symptoms

  • Check engine light on (usually after two drive cycles)
  • Usually no noticeable change in driving

Most Likely Root Causes

  • Signal or ground wire open, connector off or corroded
  • Sensor heater failed, sensor never becomes active
  • Sensor worn out (no longer produces voltage)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0146.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank1 Sensor3.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0146?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank1 Sensor3.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank1 Sensor3.
  5. 5Clear fault memory and run a verification cycle to confirm P0146 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $113
Professional Repair (Parts + Labor)$54 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0146?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0146?

DIY replacement parts average $19–$113, while professional service averages $54–$270.

Will resetting P0146 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0146 fault code meaningP0146 repair costhow to fix P0146

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0146 Fault Code: O2 Sensor Circuit No Activity… — Fixes & Cost | FaultCodes.org