FaultCodes.org
P0104OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0104 Fault Code: Mass or Volume Air Flow Sensor A Circuit Intermittent

OBD-II P0104 (Fuel Trim & Air/O2 Metering): Mass or Volume Air Flow Sensor A Circuit Intermittent.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0104 indicates Mass or Volume Air Flow Sensor A Circuit Intermittent. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$324.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $324

What This Fault Code Means

The mass air flow sensor (MAF) sits between the air filter and the throttle or compressor and measures how much air the engine draws in; fuel quantity, load and ignition are calculated from it. Most are hot-film or hot-wire sensors that output either a voltage or, on GM, Saab and newer Ford systems, a frequency. P0104 covers brief dropouts or jumps in the signal without a permanent low or high fault – the classic sign of a loose contact. In Ford's 2020–2023 petrol summary the code is set once more than 25 short open or short-circuit events have been counted. GM and Saab do not list P0104 in the documents checked; there such dropouts end up under P0102/P0103 or P0101. The trip count is not stated by Ford. Diagnosis means moving the harness while watching the live signal and checking terminals for corrosion and weak tension.

Common Symptoms

  • Check engine light on, may go out again
  • Occasional hesitation, misfire-like stumble, flat spot
  • Intermittent rough idle or stalling

Most Likely Root Causes

  • Loose contact at the sensor connector (corrosion, spread terminals, broken latch)
  • Chafed or partly broken wire moved by the engine
  • Sensor electronics dropping out (temperature-dependent)
  • Poor ground or electrical interference

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0104.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Mass Air Flow Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0104?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Mass Air Flow Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Mass Air Flow Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0104 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $136
Professional Repair (Parts + Labor)$43 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P0104?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0104?

DIY replacement parts average $16–$136, while professional service averages $43–$324.

Will resetting P0104 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0104 fault code meaningP0104 repair costhow to fix P0104

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0104 Fault Code: Mass or Volume Air Flow Sensor A… — Fixes & Cost | FaultCodes.org