FaultCodes.org
P013DOBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P013D Fault Code: O2 Sensor Slow Response - Lean to Rich Bank 2 Sensor 2

OBD-II P013D (Fuel Trim & Air/O2 Metering): O2 Sensor Slow Response - Lean to Rich Bank 2 Sensor 2.

Quick AnswerModerate — Plan Repair

OBD-II fault code P013D indicates O2 Sensor Slow Response - Lean to Rich Bank 2 Sensor 2. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$65 – $270

What This Fault Code Means

The downstream oxygen sensor (sensor 2, after the catalytic converter) is used for fine mixture trim and to monitor the converter. 'Slow response' means the signal transition itself is too sluggish – it takes too long to pass between two voltage levels. This code covers the lean-to-rich direction, tested when fuel returns or the control module briefly enriches the mixture. Bank 2 only exists on V and boxer engines. GM forces the test itself and measures how quickly the signal passes from 350 to 650 mV relative to air flow; a filtered value above its limit sets the code after one trip (fallback: target not reached before about 200 g of air). Only GM documents this direction for bank 2 among the manufacturers checked. CARB requires separate detection of slow and delayed faults in each direction (phased in from 2009 for downstream and 2011 for upstream sensors).

Common Symptoms

  • Check engine light on
  • Usually no noticeable change in driving
  • Catalyst monitor may stay incomplete (inspection readiness missing)
  • With a converter cause, P0420/P0430 may follow

Most Likely Root Causes

  • Downstream oxygen sensor aged or contaminated (soot, oil, silicone, coolant)
  • Exhaust leak between manifold/turbo and the sensor
  • Converter faulty or non-original with different oxygen storage
  • Control module software too sensitive (update available)
  • Sensor connector or wiring with contact resistance

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P013D.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank2 Sensor2.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P013D?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank2 Sensor2.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank2 Sensor2.
  5. 5Clear fault memory and run a verification cycle to confirm P013D does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $113
Professional Repair (Parts + Labor)$65 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P013D?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P013D?

DIY replacement parts average $23–$113, while professional service averages $65–$270.

Will resetting P013D fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P013D fault code meaningP013D repair costhow to fix P013D

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P013D Fault Code: O2 Sensor Slow Response - Lean to… — Fixes & Cost | FaultCodes.org