FaultCodes.org
P0140OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0140 Fault Code: O2 Sensor Circuit No Activity Detected Bank 1 Sensor 2

OBD-II P0140 (Fuel Trim & Air/O2 Metering): O2 Sensor Circuit No Activity Detected Bank 1 Sensor 2.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0140 indicates O2 Sensor Circuit No Activity Detected Bank 1 Sensor 2. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$54 – $270

What This Fault Code Means

The oxygen sensor after the catalytic converter on bank 1 (sensor 2) is a switching sensor (about 0.1–0.9 V) used for converter monitoring and fine mixture trim. P0140 means the sensor produces no voltage of its own and the control module only sees its own reference (bias) voltage. GM's V6 sets it when the signal sits at 401–548 mV or the sensor's internal resistance exceeds 40 kΩ when it should be hot; newer GM systems apply 1900 mV and read above 1700 mV as an open circuit. Two trips. Ford reports 'no activity' under P0136 instead. A cold sensor with a failed heater can also cause it. When it fails, the control module stops the downstream trim and cannot evaluate the converter; there is no limp mode.

Common Symptoms

  • Check engine light on (usually after two drive cycles)
  • Catalyst monitor readiness not set
  • Live data: sensor 2 stuck at about 450 mV (or 1.9 V)

Most Likely Root Causes

  • Signal or ground wire open, connector off or corroded
  • Sensor heater failed, sensor never becomes active
  • Sensor worn out (no longer produces voltage)
  • Control module input faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0140.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank1 Sensor2.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0140?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank1 Sensor2.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank1 Sensor2.
  5. 5Clear fault memory and run a verification cycle to confirm P0140 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $113
Professional Repair (Parts + Labor)$54 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0140?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0140?

DIY replacement parts average $19–$113, while professional service averages $54–$270.

Will resetting P0140 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0140 fault code meaningP0140 repair costhow to fix P0140

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0140 Fault Code: O2 Sensor Circuit No Activity… — Fixes & Cost | FaultCodes.org