FaultCodes.org
P0103OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0103 Fault Code: Mass or Volume Air Flow Sensor A Circuit High

OBD-II P0103 (Fuel Trim & Air/O2 Metering): Mass or Volume Air Flow Sensor A Circuit High.

Quick AnswerHigh — Service Soon

OBD-II fault code P0103 indicates Mass or Volume Air Flow Sensor A Circuit High. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$324.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $324

What This Fault Code Means

The mass air flow sensor (MAF) sits between the air filter and the throttle or compressor and measures how much air the engine draws in; fuel quantity, load and ignition are calculated from it. Most are hot-film or hot-wire sensors that output either a voltage or, on GM, Saab and newer Ford systems, a frequency. P0103 means the signal is above its electrical upper limit. Documented limits: GM petrol 14,500 Hz or more, GM diesel above 12,500 Hz, Saab 9-4X above about 15,150 Hz, Ford analogue above 4.785 V (checked only below 4,000 rpm so that high load is not mistaken for a fault). Typical causes are a signal wire shorted to a voltage source, failed sensor electronics or interference from a harness routed too close to ignition coils, relays or motors. GM and Saab need two trips; the engine switches to a calculated air mass.

Common Symptoms

  • Check engine light on
  • Substitute value mode, lack of power
  • Rich mixture possible (smoke, consumption)
  • Rough idle, hesitation

Most Likely Root Causes

  • Signal wire shorted to voltage or to the supply wire
  • Sensor electronics failed
  • Interference from harness routed near ignition coils, relays or motors
  • Water in the connector or on the element

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0103.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Mass Air Flow Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0103?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Mass Air Flow Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Mass Air Flow Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0103 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $136
Professional Repair (Parts + Labor)$43 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P0103?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0103?

DIY replacement parts average $16–$136, while professional service averages $43–$324.

Will resetting P0103 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0103 fault code meaningP0103 repair costhow to fix P0103

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0103 Fault Code: Mass or Volume Air Flow Sensor A Circuit High | FaultCodes.org