FaultCodes.org
P0130OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0130 Fault Code: O2 Sensor Circuit Bank 1 Sensor 1

OBD-II P0130 (Fuel Trim & Air/O2 Metering): O2 Sensor Circuit Bank 1 Sensor 1.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0130 indicates O2 Sensor Circuit Bank 1 Sensor 1. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$378.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$65 – $378

What This Fault Code Means

The oxygen sensor before the catalytic converter on bank 1 (sensor 1) is the main control sensor for the mixture. It is either a switching sensor (about 0.1 V lean to 0.9 V rich) or a wide-band sensor that works with a pump current evaluated by an interface chip. P0130 is the general circuit code, and manufacturers fill it very differently. Ford used it up to 2010 as the collective code for all wiring faults reported by the wide-band interface chip and has split it into specific codes since 2011. Subaru sets it when the interface voltages leave their range for 5 s, with immediate MIL. GM calls it 'closed loop performance': cross-talk from the heater (signal rises above 2 V with the heater off) or disagreement with the downstream sensor, two trips. A stored code usually switches mixture control to open loop and suspends adaptation and converter monitoring.

Common Symptoms

  • Check engine light on
  • Higher consumption, possibly rough running (no mixture control)
  • Higher emissions, possible emissions test failure
  • Sensor and catalyst readiness not set

Most Likely Root Causes

  • Wiring or connector of the bank 1 upstream sensor damaged, corroded or wet
  • Oxygen sensor faulty internally
  • Exhaust leak ahead of the sensor or mixture fault (plausibility versions)
  • Wrong or aftermarket sensor type
  • Control module or sensor interface chip faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0130.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank1 Sensor1.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0130?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank1 Sensor1.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank1 Sensor1.
  5. 5Clear fault memory and run a verification cycle to confirm P0130 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $159
Professional Repair (Parts + Labor)$65 – $378

Frequently Asked Questions

Is it safe to keep operating with fault code P0130?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0130?

DIY replacement parts average $23–$159, while professional service averages $65–$378.

Will resetting P0130 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0130 fault code meaningP0130 repair costhow to fix P0130

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0130 Fault Code: O2 Sensor Circuit Bank 1 Sensor 1 — Fixes & Cost | FaultCodes.org