FaultCodes.org
P0109OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0109 Fault Code: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Intermittent

OBD-II P0109 (Fuel Trim & Air/O2 Metering): Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Intermittent.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0109 indicates Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Intermittent. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$216.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $216

What This Fault Code Means

The manifold absolute pressure (MAP) sensor measures the pressure behind the throttle; on vehicles without a separate barometric sensor it also supplies the ambient pressure, read at key-on or wide-open throttle – hence 'MAP/BARO'. It is a three-wire sensor with 5 V reference, ground and signal. P0109 counts brief range violations of the signal that are too short for P0107/P0108 – the typical signature of a loose contact. Ford counts excursions below 0.024 V or above 4.96 V and sets the code after 25 events per drive cycle (2020–2023; ten in 2012). Ford treated it as a code without warning light in 2012 but lights the MIL in 2020–2023, so the warning-light behaviour depends on the manufacturer. GM does not use P0109 in the tables checked; there short dropouts accumulate in P0107/P0108.

Common Symptoms

  • Check engine light on (depending on manufacturer)
  • Occasional hesitation or stumble
  • Fault comes and goes

Most Likely Root Causes

  • Loose contact at the MAP connector, terminals spread or corroded
  • Chafed or broken wire that makes contact with engine movement
  • Sensor with internal dropouts
  • Ground problem or control module

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0109.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Manifold Absolute Pressure Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0109?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Manifold Absolute Pressure Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Manifold Absolute Pressure Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0109 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $91
Professional Repair (Parts + Labor)$43 – $216

Frequently Asked Questions

Is it safe to keep operating with fault code P0109?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0109?

DIY replacement parts average $16–$91, while professional service averages $43–$216.

Will resetting P0109 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0109 fault code meaningP0109 repair costhow to fix P0109

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0109 Fault Code: Manifold Absolute… — Fixes & Cost | FaultCodes.org