FaultCodes.org
P0136OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0136 Fault Code: O2 Sensor Circuit Bank 1 Sensor 2

OBD-II P0136 (Fuel Trim & Air/O2 Metering): O2 Sensor Circuit Bank 1 Sensor 2.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0136 indicates O2 Sensor Circuit Bank 1 Sensor 2. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$65 – $270

What This Fault Code Means

The oxygen sensor after the catalytic converter on bank 1 (sensor 2) is a switching sensor (about 0.1–0.9 V) used for converter monitoring and fine mixture trim. P0136 is the general circuit code, and its exact meaning varies by manufacturer. Ford sets it as 'no activity' in a functional check: if the sensor never swings beyond about 0.42/0.48 V despite rich and lean phases – if needed after forced enrichment and leaning – once per drive cycle. Opel/GM Europe set it if the average voltage stays outside 400–500 mV after 10 min of closed loop; older Bosch Motronic if it stays at 0 V for 200 s despite heating. GM North America does not use P0136. When it fails, the control module stops the downstream trim and cannot evaluate the converter; there is no limp mode.

Common Symptoms

  • Check engine light on (usually after two drive cycles)
  • Catalyst monitor readiness not set
  • Slightly higher consumption possible without downstream trim

Most Likely Root Causes

  • Downstream sensor aged or poisoned (stays in the middle band)
  • Signal or ground wire open or high-resistance, connector corroded
  • Sensor heater failed (sensor stays cold)
  • Exhaust leak ahead of the sensor
  • Control module or software

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0136.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank1 Sensor2.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0136?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank1 Sensor2.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank1 Sensor2.
  5. 5Clear fault memory and run a verification cycle to confirm P0136 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $113
Professional Repair (Parts + Labor)$65 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0136?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0136?

DIY replacement parts average $23–$113, while professional service averages $65–$270.

Will resetting P0136 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0136 fault code meaningP0136 repair costhow to fix P0136

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0136 Fault Code: O2 Sensor Circuit Bank 1 Sensor 2 — Fixes & Cost | FaultCodes.org