FaultCodes.org
P0149OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0149 Fault Code: Fuel Timing Error

OBD-II P0149 (Fuel Trim & Air/O2 Metering): Fuel Timing Error.

Quick AnswerHigh — Service Soon

OBD-II fault code P0149 indicates Fuel Timing Error. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $108–$3240.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Fuel Trim & Air/O2 Metering
Professional Repair
$108 – $3,240

What This Fault Code Means

P0149 is a diesel code for a deviation of the actual from the target start of injection. On distributor pumps such as the Bosch VP44, a timing device sets the delivery start, and the pump control unit compares the actual position with the target. On the 2003 Saab 9-3 2.2 TiD (GM/Opel engine) P0149 means injection too early – too late is the manufacturer code P1149; it is monitored continuously above 600 rpm and leads to limp mode with limited fuel quantity. CARB has required injection timing monitoring for all diesels since model year 2010. On common-rail systems timing is mostly covered by injector-related codes, so P0149 is rare there.

Common Symptoms

  • Check engine light on
  • Limp mode with power limitation
  • Starting problems up to no start
  • Smoke, knocking, rough running

Most Likely Root Causes

  • Injection pump wrongly set or drive (belt, key) shifted
  • Timing device or timing solenoid of the pump faulty
  • Air in the fuel or low supply pressure
  • Pump control unit faulty
  • Crankshaft or camshaft signal disturbed

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0149.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Injection Pump.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0149?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Injection Pump.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Injection Pump.
  5. 5Clear fault memory and run a verification cycle to confirm P0149 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$38 – $1,361
Professional Repair (Parts + Labor)$108 – $3,240

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: P0149 (Fuel Trim & Air/O2 Metering)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $108 – $3,240

Frequently Asked Questions

Is it safe to keep operating with fault code P0149?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0149?

DIY replacement parts average $38–$1361, while professional service averages $108–$3240.

Will resetting P0149 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0149 fault code meaningP0149 repair costhow to fix P0149

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0149 Fault Code: Fuel Timing Error — Causes, Fixes & Cost | FaultCodes.org