FaultCodes.org
P0144OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0144 Fault Code: O2 Sensor Circuit High Voltage Bank 1 Sensor 3

OBD-II P0144 (Fuel Trim & Air/O2 Metering): O2 Sensor Circuit High Voltage Bank 1 Sensor 3.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0144 indicates O2 Sensor Circuit High Voltage Bank 1 Sensor 3. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$65 – $270

What This Fault Code Means

Sensor 3 is a third oxygen sensor on bank 1, behind a second converter or converter brick. It only exists on some vehicles – documented for Jaguar Land Rover's 3.0 V6 supercharged (2013–2016, where sensor 2 is 'mid-cat' and sensor 3 'post-cat') and Ford systems that monitor part of the converter volume. P0144 means the signal of sensor 3 stays above its upper limit, usually because the heater supply or another voltage reaches the signal wire. Ford's over-voltage test (above 1.1 V for 10 s, after 90 s of heating) explicitly covers downstream sensors 2 and 3; Jaguar Land Rover lists the code for its post-cat sensor. When it fails, the control module stops the downstream trim and cannot evaluate the converter; there is no limp mode.

Common Symptoms

  • Check engine light on (usually after two drive cycles)
  • Catalyst monitor readiness not set
  • Usually no noticeable change in driving

Most Likely Root Causes

  • Signal wire shorted to heater supply or battery voltage
  • Sensor faulty internally (heater-to-signal short)
  • Signal circuit open or high-resistance (GM bias logic)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0144.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank1 Sensor3.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0144?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank1 Sensor3.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank1 Sensor3.
  5. 5Clear fault memory and run a verification cycle to confirm P0144 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $113
Professional Repair (Parts + Labor)$65 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0144?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0144?

DIY replacement parts average $23–$113, while professional service averages $65–$270.

Will resetting P0144 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0144 fault code meaningP0144 repair costhow to fix P0144

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0144 Fault Code: O2 Sensor Circuit High Voltage Bank 1 Sensor 3 | FaultCodes.org