FaultCodes.org
P0105OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0105 Fault Code: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit

OBD-II P0105 (Fuel Trim & Air/O2 Metering): Manifold Absolute Pressure/Barometric Pressure Sensor Circuit.

Quick AnswerHigh — Service Soon

OBD-II fault code P0105 indicates Manifold Absolute Pressure/Barometric Pressure Sensor Circuit. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$216.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $216

What This Fault Code Means

The manifold absolute pressure (MAP) sensor measures the pressure behind the throttle; on vehicles without a separate barometric sensor it also supplies the ambient pressure, read at key-on or wide-open throttle – hence 'MAP/BARO'. It is a three-wire sensor with 5 V reference, ground and signal. P0105 is the general circuit fault and is rarely used today: most petrol engines report low, high and intermittent separately (P0107–P0109). It appears mainly where the fault cannot be broken down further – Ford's 2023 diesels set it when the digital SENT sensor reports a bad status or an out-of-limit value for 5 s (lost communication is a separate U code), and Bosch EDC16 diesels use it with a fault type byte, for example signal below 0.2 V. Saab then substitutes 101.3 kPa, limits torque and switches off EGR and boost control.

Common Symptoms

  • Check engine light on
  • Loss of power, limp mode with torque limit (diesel)
  • Rough idle, hard starting, higher consumption (petrol)
  • Smoke possible on diesels

Most Likely Root Causes

  • Connector or wiring to the sensor open, shorted or loose
  • MAP sensor faulty (oiled, failed internally, SENT status fault)
  • Sensor hose disconnected, vacuum or boost leak
  • 5 V reference pulled down by another sensor on the same circuit
  • Engine control module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0105.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Manifold Absolute Pressure Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0105?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Manifold Absolute Pressure Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Manifold Absolute Pressure Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0105 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $91
Professional Repair (Parts + Labor)$43 – $216

Frequently Asked Questions

Is it safe to keep operating with fault code P0105?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0105?

DIY replacement parts average $16–$91, while professional service averages $43–$216.

Will resetting P0105 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0105 fault code meaningP0105 repair costhow to fix P0105

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0105 Fault Code: Manifold Absolute… — Fixes & Cost | FaultCodes.org