FaultCodes.org
P010EOBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P010E Fault Code: Mass or Volume Air Flow Sensor B Circuit Intermittent/Erratic

OBD-II P010E (Fuel Trim & Air/O2 Metering): Mass or Volume Air Flow Sensor B Circuit Intermittent/Erratic.

Quick AnswerModerate — Plan Repair

OBD-II fault code P010E indicates Mass or Volume Air Flow Sensor B Circuit Intermittent/Erratic. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $43–$378.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $378

What This Fault Code Means

Sensor B is a second mass air flow sensor in a second intake path, found on engines with two air filter boxes – for example the Nissan VR30DDTT twin-turbo V6 (where sensor B belongs to bank 2) or GM's 3.0 litre twin-turbo V6. P010E covers brief dropouts or jumps in the signal of sensor B without a lasting low or high fault, the counterpart of P0104. Ford's 2020–2023 petrol summary sets it after more than 25 short open or short-circuit events; GM's twin-turbo V6 does not use it, and Ford does not state the trip count. The usual cause is a loose contact at the connector or a chafed wire that opens as the engine moves.

Common Symptoms

  • Check engine light on, may come and go
  • Occasional hesitation or stumble
  • Intermittent loss of power

Most Likely Root Causes

  • Loose contact at the sensor B connector
  • Chafed or partly broken wire
  • Sensor B electronics dropping out
  • Poor ground or interference

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P010E.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Mass Air Flow Sensor B.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P010E?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Mass Air Flow Sensor B.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Mass Air Flow Sensor B.
  5. 5Clear fault memory and run a verification cycle to confirm P010E does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $159
Professional Repair (Parts + Labor)$43 – $378

Frequently Asked Questions

Is it safe to keep operating with fault code P010E?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P010E?

DIY replacement parts average $16–$159, while professional service averages $43–$378.

Will resetting P010E fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P010E fault code meaningP010E repair costhow to fix P010E

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P010E Fault Code: Mass or Volume Air Flow Sensor B… — Fixes & Cost | FaultCodes.org