FaultCodes.org
P010FOBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P010F Fault Code: Mass or Volume Air Flow Sensor A/B Correlation

OBD-II P010F (Fuel Trim & Air/O2 Metering): Mass or Volume Air Flow Sensor A/B Correlation.

Quick AnswerHigh — Service Soon

OBD-II fault code P010F indicates Mass or Volume Air Flow Sensor A/B Correlation. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$756.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $756

What This Fault Code Means

Engines with two intake paths have two mass air flow sensors, A and B. On a symmetrical V engine both sides should draw about the same amount of air, so the readings can be compared with each other. P010F is set when both signals are electrically valid but differ by more than allowed; the code does not say which side is wrong. No manufacturer document using exactly this code or its threshold was found: GM's twin-turbo V6 and Nissan's VR30DDTT assess each sensor separately against a model (P0101/P010B). The description therefore rests on the CARB requirement for plausibility checks and on component sources for engines with two sensors. Typical causes are a leaking intake pipe or a soiled sensor on one side.

Common Symptoms

  • Check engine light on
  • Lack of power, uneven running
  • Mixture codes for one bank (P0171/P0174) possible

Most Likely Root Causes

  • Air leak or loose intake pipe on one side
  • One of the two sensors contaminated or aged
  • Air filter on one side clogged or wrongly fitted
  • Turbocharger or boost problem on one bank
  • Contact resistance in connector or wiring

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P010F.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Mass Air Flow Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P010F?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Mass Air Flow Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Mass Air Flow Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P010F does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $318
Professional Repair (Parts + Labor)$43 – $756

Frequently Asked Questions

Is it safe to keep operating with fault code P010F?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P010F?

DIY replacement parts average $16–$318, while professional service averages $43–$756.

Will resetting P010F fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P010F fault code meaningP010F repair costhow to fix P010F

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P010F Fault Code: Mass or Volume Air Flow Sensor A/B Correlation | FaultCodes.org