FaultCodes.org
P0108OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0108 Fault Code: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High

OBD-II P0108 (Fuel Trim & Air/O2 Metering): Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High.

Quick AnswerHigh — Service Soon

OBD-II fault code P0108 indicates Manifold Absolute Pressure/Barometric Pressure Sensor Circuit High. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$216.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $216

What This Fault Code Means

The manifold absolute pressure (MAP) sensor measures the pressure behind the throttle; on vehicles without a separate barometric sensor it also supplies the ambient pressure, read at key-on or wide-open throttle – hence 'MAP/BARO'. It is a three-wire sensor with 5 V reference, ground and signal. P0108 means the signal voltage is above its upper limit – typically an open ground (low reference), a signal wire shorted to 5 V or battery voltage, or a failed sensor. Like P0107 it describes the voltage, not real overpressure; genuinely excessive boost is P0234. Documented limits: GM petrol above 86 % of 5 V, GM diesel above 97 %, GM/Saab 2.0T above 4.80 V for 4 s, Ford above 4.88–4.96 V for 5 s. The engine substitutes a modelled value, which often makes the mixture too rich; turbo engines limit boost.

Common Symptoms

  • Check engine light on
  • Rich mixture, sooting, higher consumption
  • Rough idle, loss of power or limp mode on turbo engines

Most Likely Root Causes

  • Ground (low reference) wire open or connector corroded
  • Signal wire shorted to 5 V or battery voltage
  • MAP sensor failed internally
  • Engine control module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0108.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Manifold Absolute Pressure Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0108?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Manifold Absolute Pressure Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Manifold Absolute Pressure Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0108 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $91
Professional Repair (Parts + Labor)$43 – $216

Frequently Asked Questions

Is it safe to keep operating with fault code P0108?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0108?

DIY replacement parts average $16–$91, while professional service averages $43–$216.

Will resetting P0108 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0108 fault code meaningP0108 repair costhow to fix P0108

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0108 Fault Code: Manifold Absolute… — Fixes & Cost | FaultCodes.org