P013C Fault Code: O2 Sensor Slow Response - Rich to Lean Bank 2 Sensor 2
OBD-II P013C (Fuel Trim & Air/O2 Metering): O2 Sensor Slow Response - Rich to Lean Bank 2 Sensor 2.
OBD-II fault code P013C indicates O2 Sensor Slow Response - Rich to Lean Bank 2 Sensor 2. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$270.
- Safe to Operate?
- Yes (Short Term)
- DIY Difficulty
- Easy (Basic Tools)
- System
- Fuel Trim & Air/O2 Metering
- Professional Repair
- $65 – $270
What This Fault Code Means
The downstream oxygen sensor (sensor 2, after the catalytic converter) is used for fine mixture trim and to monitor the converter. 'Slow response' means the signal transition itself is too sluggish – it takes too long to pass between two voltage levels. This code covers the rich-to-lean direction, usually tested during deceleration fuel cut-off. Bank 2 only exists on V and boxer engines. GM forces the test itself and measures how quickly the signal passes from 450 to 150 mV relative to air flow; a filtered value above its limit sets the code after one trip (fallback: target not reached before about 70 g of air). Ford reports the same slew-rate test for bank 2 under this code. CARB requires separate detection of slow and delayed faults in each direction (phased in from 2009 for downstream and 2011 for upstream sensors).
Common Symptoms
- Check engine light on
- Usually no noticeable change in driving
- Catalyst monitor may stay incomplete (inspection readiness missing)
- With a converter cause, P0420/P0430 may follow
Most Likely Root Causes
- Downstream oxygen sensor aged or contaminated (soot, oil, silicone, coolant)
- Exhaust leak between manifold/turbo and the sensor
- Converter faulty or non-original with different oxygen storage
- Control module software too sensitive (update available)
- Sensor connector or wiring with contact resistance
Diagnostic Checks Before Replacing Parts
Verify the exact faulty component before ordering replacements.
- 1Read stored freeze-frame data and companion codes alongside P013C.
- 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank2 Sensor2.
- 3Verify live sensor telemetry before ordering replacement components.
Interactive Symptom Triage
Answer 3 quick checks to narrow down the faulty component before spending money on parts.
Are any companion fault codes stored alongside P013C?
Step-by-Step Troubleshooting & Fix
- 1Scan for companion fault codes and address upstream circuit issues first.
- 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank2 Sensor2.
- 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
- 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank2 Sensor2.
- 5Clear fault memory and run a verification cycle to confirm P013C does not return.
Estimated Repair Cost Benchmark
Typical DIY parts and certified technician labor ranges. Select a currency below.
| Repair Path | USD |
|---|---|
| DIY Parts Only | $23 – $113 |
| Professional Repair (Parts + Labor) | $65 – $270 |
Frequently Asked Questions
Is it safe to keep operating with fault code P013C?
Usually safe for short trips if no severe drivability or safety warnings are active.
How much does it cost to repair P013C?
DIY replacement parts average $23–$113, while professional service averages $65–$270.
Will resetting P013C fix the problem permanently?
No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.
Related Searches & Questions
Manufacturer & Technical Reference
OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)