FaultCodes.org
P0139OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0139 Fault Code: O2 Sensor Circuit Slow Response Bank 1 Sensor 2

OBD-II P0139 (Fuel Trim & Air/O2 Metering): O2 Sensor Circuit Slow Response Bank 1 Sensor 2.

Quick AnswerModerate — Plan Repair

OBD-II fault code P0139 indicates O2 Sensor Circuit Slow Response Bank 1 Sensor 2. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$65 – $270

What This Fault Code Means

The oxygen sensor after the catalytic converter on bank 1 (sensor 2) is a switching sensor (about 0.1–0.9 V) used for converter monitoring and fine mixture trim. P0139 means the sensor reacts too slowly to mixture changes. Subaru measures it around fuel cut-off: rich to lean from 500 to 300 mV must take no more than 0.51 s, lean to rich from 300 to 500 mV no more than 2 s; two drive cycles set the MIL. CARB requires such a test because a sluggish downstream sensor could let a worn converter pass. Since about 2009–2011 GM and Ford report this as direction-specific codes P013A–P013F instead; P0139 remains in use on older, Asian and Jaguar Land Rover systems. When it fails, the control module stops the downstream trim and cannot evaluate the converter; there is no limp mode.

Common Symptoms

  • Check engine light on (usually after two drive cycles)
  • Catalyst monitor readiness not set
  • P0420 may follow

Most Likely Root Causes

  • Sensor aged or contaminated (oil ash, silicone, additives)
  • Exhaust leak ahead of the sensor
  • Sensor heater weak, sensor too cold
  • High-resistance ground or connector

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0139.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank1 Sensor2.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0139?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank1 Sensor2.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank1 Sensor2.
  5. 5Clear fault memory and run a verification cycle to confirm P0139 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $113
Professional Repair (Parts + Labor)$65 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P0139?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0139?

DIY replacement parts average $23–$113, while professional service averages $65–$270.

Will resetting P0139 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0139 fault code meaningP0139 repair costhow to fix P0139

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0139 Fault Code: O2 Sensor Circuit Slow Response Bank 1 Sensor 2 | FaultCodes.org