FaultCodes.org
P0107OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0107 Fault Code: Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Low

OBD-II P0107 (Fuel Trim & Air/O2 Metering): Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Low.

Quick AnswerHigh — Service Soon

OBD-II fault code P0107 indicates Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Low. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$216.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $216

What This Fault Code Means

The manifold absolute pressure (MAP) sensor measures the pressure behind the throttle; on vehicles without a separate barometric sensor it also supplies the ambient pressure, read at key-on or wide-open throttle – hence 'MAP/BARO'. It is a three-wire sensor with 5 V reference, ground and signal. P0107 means the signal voltage is below its lower limit. 'Low' refers to the voltage, not to a real low pressure: typically the signal wire is grounded, the signal or 5 V reference is open, or the sensor has failed. A short on another sensor sharing the same reference can pull it down too, so GM often sees several codes at once. Documented limits: GM below 3.3 % of 5 V (about 0.17 V), GM/Saab 2.0T below 0.19 V for 4 s, Ford petrol below 0.19 V for 5 s, Ford diesel below 0.1 V. GM petrol needs two trips, GM diesel one. A modelled value replaces the reading.

Common Symptoms

  • Check engine light on
  • Hard starting, rough idle, stalling possible
  • Wrong mixture from substitute value, higher consumption
  • Loss of power or limp mode on turbo and diesel engines

Most Likely Root Causes

  • Connector unplugged or corroded, signal or reference wire open
  • Signal wire shorted to ground (chafing)
  • 5 V reference shorted by another faulty sensor on the same circuit
  • MAP sensor failed internally
  • Engine control module faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0107.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Manifold Absolute Pressure Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0107?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Manifold Absolute Pressure Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Manifold Absolute Pressure Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0107 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $91
Professional Repair (Parts + Labor)$43 – $216

Frequently Asked Questions

Is it safe to keep operating with fault code P0107?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0107?

DIY replacement parts average $16–$91, while professional service averages $43–$216.

Will resetting P0107 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0107 fault code meaningP0107 repair costhow to fix P0107

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0107 Fault Code: Manifold Absolute… — Fixes & Cost | FaultCodes.org