FaultCodes.org
P0100OBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P0100 Fault Code: Mass or Volume Air Flow Sensor A Circuit

OBD-II P0100 (Fuel Trim & Air/O2 Metering): Mass or Volume Air Flow Sensor A Circuit.

Quick AnswerHigh — Service Soon

OBD-II fault code P0100 indicates Mass or Volume Air Flow Sensor A Circuit. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $43–$324.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$43 – $324

What This Fault Code Means

The mass air flow sensor (MAF) sits between the air filter and the throttle or compressor and measures how much air the engine draws in; fuel quantity, load and ignition are calculated from it. Most are hot-film or hot-wire sensors that output either a voltage or, on GM, Saab and newer Ford systems, a frequency. P0100 means the control module gets no usable signal at all. Ford uses it for a broken sensing element on digital sensors (period longer than 1.3 ms, i.e. below about 0.78 kHz, for half a second); on GM's 3.0 V6 in the Saab 9-4X it is set at 0 Hz. Many systems with voltage sensors skip P0100 and report low or high directly. The engine then runs on air mass calculated from manifold pressure, throttle angle and speed; Ford also disables start-stop.

Common Symptoms

  • Check engine light on
  • Rough idle, hesitation, lack of power (substitute value)
  • Hard starting or stalling
  • Higher fuel consumption

Most Likely Root Causes

  • Connector unplugged or corroded, signal or supply wire open
  • Sensor faulty internally (broken element, failed electronics)
  • Supply fuse or relay failed
  • Control module input faulty

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0100.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Mass Air Flow Sensor.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0100?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Mass Air Flow Sensor.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Mass Air Flow Sensor.
  5. 5Clear fault memory and run a verification cycle to confirm P0100 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$16 – $136
Professional Repair (Parts + Labor)$43 – $324

Frequently Asked Questions

Is it safe to keep operating with fault code P0100?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0100?

DIY replacement parts average $16–$136, while professional service averages $43–$324.

Will resetting P0100 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0100 fault code meaningP0100 repair costhow to fix P0100

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P0100 Fault Code: Mass or Volume Air Flow Sensor A Circuit | FaultCodes.org