FaultCodes.org
P014AOBD-IIFuel Trim & Air/O2 MeteringTechnical Reference· Updated: Nov 22, 2026

P014A Fault Code: O2 Sensor Delayed Response - Rich to Lean Bank 2 Sensor 2

OBD-II P014A (Fuel Trim & Air/O2 Metering): O2 Sensor Delayed Response - Rich to Lean Bank 2 Sensor 2.

Quick AnswerModerate — Plan Repair

OBD-II fault code P014A indicates O2 Sensor Delayed Response - Rich to Lean Bank 2 Sensor 2. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$270.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Easy (Basic Tools)
System
Fuel Trim & Air/O2 Metering
Professional Repair
$65 – $270

What This Fault Code Means

The downstream oxygen sensor (sensor 2, after the catalytic converter) is used for fine mixture trim and to monitor the converter. 'Delayed response' means the sensor starts reacting too late, or does not reach the target level at all, after the mixture has changed. This code covers the rich-to-lean direction, usually tested during deceleration fuel cut-off. Bank 2 only exists on V and boxer engines. GM checks whether the signal falls below 450 mV before about 45 g of air have passed after the forced change; failing needs two trips. Ford uses the same stuck-in-range test for bank 2, failing after three bad results in a row. CARB requires separate detection of slow and delayed faults in each direction (phased in from 2009 for downstream and 2011 for upstream sensors).

Common Symptoms

  • Check engine light on
  • Usually no noticeable change in driving
  • Catalyst monitor may stay incomplete (inspection readiness missing)
  • With a converter cause, P0420/P0430 may follow

Most Likely Root Causes

  • Downstream oxygen sensor aged or contaminated (soot, oil, silicone, coolant)
  • Exhaust leak between manifold/turbo and the sensor
  • Converter faulty or non-original with different oxygen storage
  • Control module software too sensitive (update available)
  • Sensor connector or wiring with contact resistance

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P014A.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Oxygen Sensor Bank2 Sensor2.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P014A?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Oxygen Sensor Bank2 Sensor2.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Oxygen Sensor Bank2 Sensor2.
  5. 5Clear fault memory and run a verification cycle to confirm P014A does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $113
Professional Repair (Parts + Labor)$65 – $270

Frequently Asked Questions

Is it safe to keep operating with fault code P014A?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P014A?

DIY replacement parts average $23–$113, while professional service averages $65–$270.

Will resetting P014A fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P014A fault code meaningP014A repair costhow to fix P014A

Manufacturer & Technical Reference

OBD-II Technical Reference (Fuel Trim & Air/O2 Metering)

Related Fault Codes

Auto & OBD-II →
P014A Fault Code: O2 Sensor Delayed Response - Rich… — Fixes & Cost | FaultCodes.org