FaultCodes.org
U0042OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0042 Fault Code: Vehicle Communication Bus B (-) Open

OBD-II U0042 (CAN Bus & Network Communication): Vehicle Communication Bus B (-) Open.

Quick AnswerModerate — Plan Repair

OBD-II fault code U0042 indicates Vehicle Communication Bus B (-) Open. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$756.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Professional Recommended
System
CAN Bus & Network Communication
Professional Repair
$65 – $756

What This Fault Code Means

U0042 points to an interrupted (-) wire on Vehicle Communication Bus B; on a CAN-type bus that is CAN-Low. The network then splits along the break, and on a standard high-speed CAN neither side's transceiver can tell what happened, since NXP states that line interruptions escape even transceiver diagnosis. Detection rests on time-outs for messages from nodes on the far side. On a fault-tolerant low-speed CAN, the TJA1055 data sheet from NXP treats a CAN-Low interruption as a failure that frames in progress survive. A resistance check across the two bus wires at a central connector helps: with both terminations reachable it reads about 60 ohms, a break in one wire leaves only the near terminator at about 120 ohms. No manufacturer documents U0042 publicly; start with connectors that were opened recently.

Common Symptoms

  • Modules beyond the break no longer respond
  • Lost-communication codes stored alongside

Most Likely Root Causes

  • (-) wire of Bus B broken in the harness
  • Corroded or pushed-back terminal in a connector
  • Connector not reconnected after a repair

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0042.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Bus B Wiring.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0042?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Bus B Wiring.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Bus B Wiring.
  5. 5Clear fault memory and run a verification cycle to confirm U0042 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $318
Professional Repair (Parts + Labor)$65 – $756

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: U0042 (CAN Bus & Network Communication)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $65 – $756

Frequently Asked Questions

Is it safe to keep operating with fault code U0042?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair U0042?

DIY replacement parts average $23–$318, while professional service averages $65–$756.

Will resetting U0042 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0042 fault code meaningU0042 repair costhow to fix U0042

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0042 Fault Code: Vehicle Communication Bus B (-) Open | FaultCodes.org