FaultCodes.org
U0027OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0027 Fault Code: Low Speed CAN Communication Bus (-) Shorted to Bus (+)

OBD-II U0027 (CAN Bus & Network Communication): Low Speed CAN Communication Bus (-) Shorted to Bus (+).

Quick AnswerModerate — Plan Repair

OBD-II fault code U0027 indicates Low Speed CAN Communication Bus (-) Shorted to Bus (+). Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$756.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
CAN Bus & Network Communication
Professional Repair
$54 – $756

What This Fault Code Means

U0027 describes the two wires of a low-speed CAN, (+) and (-), touching each other. On a high-speed bus such a short ends all traffic, but the fault-tolerant layer of ISO 11898-3 is built to ride it out. NXP's TJA1055 counts it as failure 7: the receive signal first sticks at dominant, then within about 0.3 to 1.6 ms the transceiver turns off its CAN-Low driver, leaves that wire with only a weak pull-up and carries on in single-wire mode. Comfort functions usually still work, though with less margin against interference, and differential operation resumes by itself once the short is cleared. No manufacturer documents U0027 publicly; a single-wire bus like GM's low-speed GMLAN cannot have this fault at all. Squeezed harness sections and wet splices are the likely spots; compare the high-speed sibling U0009.

Common Symptoms

  • Comfort network keeps running, sometimes with dropouts
  • Higher sensitivity to electrical interference
  • Code stored in several body modules at once

Most Likely Root Causes

  • Harness crushed so that both bus wires make contact
  • Water in a splice or connector bridging the two wires
  • Damaged transceiver bridging its two bus pins

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0027.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Low Speed Can Wiring.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0027?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Low Speed Can Wiring.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Low Speed Can Wiring.
  5. 5Clear fault memory and run a verification cycle to confirm U0027 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $318
Professional Repair (Parts + Labor)$54 – $756

Frequently Asked Questions

Is it safe to keep operating with fault code U0027?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair U0027?

DIY replacement parts average $19–$318, while professional service averages $54–$756.

Will resetting U0027 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0027 fault code meaningU0027 repair costhow to fix U0027

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0027 Fault Code: Low Speed CAN Communication Bus… — Fixes & Cost | FaultCodes.org