FaultCodes.org
U0026OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0026 Fault Code: Low Speed CAN Communication Bus (-) High

OBD-II U0026 (CAN Bus & Network Communication): Low Speed CAN Communication Bus (-) High.

Quick AnswerModerate — Plan Repair

OBD-II fault code U0026 indicates Low Speed CAN Communication Bus (-) High. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$648.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
CAN Bus & Network Communication
Professional Repair
$54 – $648

What This Fault Code Means

U0026 means CAN-Low, the (-) line of a two-wire low-speed CAN, is held too high. Since this wire already sits near 5 V at rest in an ISO 11898-3 network, the outcome depends on where the short goes. Against the 5 V supply (failure 6a in NXP's TJA1055) the transceiver stays in differential mode with normal drivers and termination. Against battery voltage (failure 6) its comparator trips after roughly 0.3 to 1.6 ms, the CAN-Low driver is switched off, the termination becomes a weak pull-up and reception continues over CAN-High alone. Either way the bus normally survives, which is why the code is often found without a clear complaint. No manufacturer documents U0026 publicly, and the GM low-speed GMLAN gets by with one conductor. Look for chafing against a feed wire or water in a connector.

Common Symptoms

  • Often no noticeable effect
  • Occasional comfort function dropouts when the bus runs on one wire

Most Likely Root Causes

  • CAN-Low chafed against a battery or ignition feed
  • Moisture in a connector linking CAN-Low to a supply pin
  • Faulty transceiver driving CAN-Low to its supply

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0026.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Low Speed Can Wiring.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0026?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Low Speed Can Wiring.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Low Speed Can Wiring.
  5. 5Clear fault memory and run a verification cycle to confirm U0026 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $272
Professional Repair (Parts + Labor)$54 – $648

Frequently Asked Questions

Is it safe to keep operating with fault code U0026?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair U0026?

DIY replacement parts average $19–$272, while professional service averages $54–$648.

Will resetting U0026 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0026 fault code meaningU0026 repair costhow to fix U0026

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0026 Fault Code: Low Speed CAN Communication Bus (-) High | FaultCodes.org