FaultCodes.org
U0025OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0025 Fault Code: Low Speed CAN Communication Bus (-) Low

OBD-II U0025 (CAN Bus & Network Communication): Low Speed CAN Communication Bus (-) Low.

Quick AnswerModerate — Plan Repair

OBD-II fault code U0025 indicates Low Speed CAN Communication Bus (-) Low. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$648.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
CAN Bus & Network Communication
Professional Repair
$54 – $648

What This Fault Code Means

U0025 flags CAN-Low pulled toward ground on a low-speed CAN with two conductors. In the fault-tolerant physical layer of ISO 11898-3 CAN-Low idles near 5 V, so a ground short forces it into its dominant state for good. NXP's TJA1055 (failure 4) first sees a permanently dominant receive signal; after about 0.3 to 1.6 ms it switches the CAN-Low driver off, changes that line's termination to a weak pull-up and continues in single-wire mode on CAN-High. Messages keep flowing, but with weaker immunity to interference, so sporadic dropouts of comfort functions are possible. The transceiver goes back to differential mode by itself once the short is gone. No manufacturer documents U0025 publicly; GM's one-conductor bus has no (-) side at all. Resistance from CAN-Low to ground near 0 Ω with the battery off confirms the fault.

Common Symptoms

  • Comfort functions work but drop out now and then
  • Body modules store the code repeatedly

Most Likely Root Causes

  • CAN-Low insulation damaged and touching body ground
  • Harness trapped by a panel, bracket or seat mechanism
  • Module transceiver internally shorting CAN-Low to ground

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0025.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Low Speed Can Wiring.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0025?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Low Speed Can Wiring.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Low Speed Can Wiring.
  5. 5Clear fault memory and run a verification cycle to confirm U0025 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $272
Professional Repair (Parts + Labor)$54 – $648

Frequently Asked Questions

Is it safe to keep operating with fault code U0025?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair U0025?

DIY replacement parts average $19–$272, while professional service averages $54–$648.

Will resetting U0025 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0025 fault code meaningU0025 repair costhow to fix U0025

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0025 Fault Code: Low Speed CAN Communication Bus (-) Low | FaultCodes.org