FaultCodes.org
U0024OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0024 Fault Code: Low Speed CAN Communication Bus (-) Open

OBD-II U0024 (CAN Bus & Network Communication): Low Speed CAN Communication Bus (-) Open.

Quick AnswerModerate — Plan Repair

OBD-II fault code U0024 indicates Low Speed CAN Communication Bus (-) Open. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$540.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
CAN Bus & Network Communication
Professional Repair
$54 – $540

What This Fault Code Means

U0024 reports an interruption of the (-) line, CAN-Low, of a two-wire low-speed CAN. Under the ISO 11898-3 fault-tolerant scheme this wire idles near 5 V and is pulled toward ground for dominant bits. NXP's TJA1055 counts a broken CAN-Low as failure 2, keeps drivers and termination as they are and goes on receiving differentially; it can flag the break only when the gap separates transmitter and receiver, which makes its error output flicker. Because the network keeps running, the fault often surfaces only as a stored code in modules beyond the break. Places where wires flex, such as door or tailgate transitions, are obvious suspects. The single-wire GM low-speed GMLAN has no (-) line, so the code has no meaning there. No manufacturer documents U0024 publicly.

Common Symptoms

  • Typically no symptom, code found during a scan
  • Comfort functions behind the break react sluggishly or sporadically

Most Likely Root Causes

  • CAN-Low wire broken in a door or tailgate harness
  • CAN-Low terminal backed out of its connector
  • Corroded CAN-Low contact after water entry

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0024.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Low Speed Can Wiring.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0024?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Low Speed Can Wiring.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Low Speed Can Wiring.
  5. 5Clear fault memory and run a verification cycle to confirm U0024 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $227
Professional Repair (Parts + Labor)$54 – $540

Frequently Asked Questions

Is it safe to keep operating with fault code U0024?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair U0024?

DIY replacement parts average $19–$227, while professional service averages $54–$540.

Will resetting U0024 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0024 fault code meaningU0024 repair costhow to fix U0024

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0024 Fault Code: Low Speed CAN Communication Bus (-) Open | FaultCodes.org