FaultCodes.org
U0023OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0023 Fault Code: Low Speed CAN Communication Bus (+) High

OBD-II U0023 (CAN Bus & Network Communication): Low Speed CAN Communication Bus (+) High.

Quick AnswerModerate — Plan Repair

OBD-II fault code U0023 indicates Low Speed CAN Communication Bus (+) High. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$648.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
CAN Bus & Network Communication
Professional Repair
$54 – $648

What This Fault Code Means

U0023 means CAN-High, the (+) conductor of a dual-line low-speed CAN, sits too high, typically shorted to battery voltage or a 5 V supply. Under ISO 11898-3 this pins the line at a level the receivers read as permanently dominant. NXP's TJA1055 handles it as failure 3 or 3a in two steps: once an initial delay expires it falls back to single-wire operation, and if the line is still too high it moves over to CAN-Low, switches its CAN-High driver off and weakens that line's termination; detection takes about 1.6 to 8 ms. Traffic continues on one wire, though electromagnetic robustness is worse in that mode. No manufacturer documents U0023 publicly; GM's low-speed GMLAN, being a single conductor, offers no (+)/(-) pair. CAN-High measuring near battery voltage against ground instead of its resting level close to 0 V points to the short.

Common Symptoms

  • Comfort functions mostly still work, occasional glitches
  • Increased sensitivity to interference, e.g. with radio transmitters nearby
  • Code stored in several body modules

Most Likely Root Causes

  • CAN-High chafed against a battery feed or ignition wire
  • Water in a connector bridging CAN-High to a supply pin
  • Retrofitted accessory tapped into the wrong wire

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0023.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Low Speed Can Wiring.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0023?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Low Speed Can Wiring.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Low Speed Can Wiring.
  5. 5Clear fault memory and run a verification cycle to confirm U0023 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $272
Professional Repair (Parts + Labor)$54 – $648

Frequently Asked Questions

Is it safe to keep operating with fault code U0023?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair U0023?

DIY replacement parts average $19–$272, while professional service averages $54–$648.

Will resetting U0023 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0023 fault code meaningU0023 repair costhow to fix U0023

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0023 Fault Code: Low Speed CAN Communication Bus (+) High | FaultCodes.org