FaultCodes.org
U0022OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0022 Fault Code: Low Speed CAN Communication Bus (+) Low

OBD-II U0022 (CAN Bus & Network Communication): Low Speed CAN Communication Bus (+) Low.

Quick AnswerModerate — Plan Repair

OBD-II fault code U0022 indicates Low Speed CAN Communication Bus (+) Low. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$648.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
CAN Bus & Network Communication
Professional Repair
$54 – $648

What This Fault Code Means

U0022 indicates a ground short on CAN-High, the positive conductor of a dual-wire low-speed CAN. In the fault-tolerant design of ISO 11898-3, where CAN-High idles at about 0 V and only rises for dominant bits, a ground short simply takes that rise away. NXP's TJA1055 lists CAN-High to ground as failure 5 and keeps transmitting and receiving differentially, since its receiver threshold is chosen so that reception stays correct in this case as well. The network therefore keeps working, and the driver often notices nothing apart from the stored code. On GM's single-wire low-speed GMLAN the (+)/(-) naming does not fit. No manufacturer documents U0022 publicly. With the battery disconnected, a reading near zero ohms from CAN-High to ground confirms the short; trim screws and seat rails are typical culprits.

Common Symptoms

  • Frequently no symptom besides the stored code
  • Rare sporadic comfort function faults

Most Likely Root Causes

  • CAN-High insulation chafed through against body ground
  • Wire pierced by a trim screw or trapped under a seat rail
  • Internal transceiver fault pulling CAN-High low

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0022.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Low Speed Can Wiring.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0022?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Low Speed Can Wiring.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Low Speed Can Wiring.
  5. 5Clear fault memory and run a verification cycle to confirm U0022 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $272
Professional Repair (Parts + Labor)$54 – $648

Frequently Asked Questions

Is it safe to keep operating with fault code U0022?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair U0022?

DIY replacement parts average $19–$272, while professional service averages $54–$648.

Will resetting U0022 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0022 fault code meaningU0022 repair costhow to fix U0022

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0022 Fault Code: Low Speed CAN Communication Bus (+) Low | FaultCodes.org