FaultCodes.org
U0021OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0021 Fault Code: Low Speed CAN Communication Bus (+) Open

OBD-II U0021 (CAN Bus & Network Communication): Low Speed CAN Communication Bus (+) Open.

Quick AnswerModerate — Plan Repair

OBD-II fault code U0021 indicates Low Speed CAN Communication Bus (+) Open. Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$540.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
CAN Bus & Network Communication
Professional Repair
$54 – $540

What This Fault Code Means

U0021 marks a break in the (+) wire of a two-wire low-speed CAN, called CAN-High in the fault-tolerant layout of ISO 11898-3. There the wire rests close to 0 V and is pulled toward 5 V for a dominant bit, the reverse of the high-speed pattern. NXP's TJA1055 treats an interrupted CAN-High as failure 1: drivers, termination and differential reception stay unchanged, and its error pin only reacts when the gap lies between sender and receiver, so it toggles rather than staying low. Communication therefore usually continues and the code mainly records lost redundancy. GM's low-speed GMLAN uses one wire only, so a (+)/(-) split does not apply there. No manufacturer documents U0021 publicly; CARB merely demands that missing communication of digital inputs be detected and coded separately.

Common Symptoms

  • Usually no noticeable effect, the bus keeps running
  • Occasional comfort function glitches, especially with interference
  • Code stored only in modules on one side of the break

Most Likely Root Causes

  • CAN-High wire broken at a flex point such as a door transition
  • Pushed-back or spread terminal in a connector
  • Corrosion in a connector or splice

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0021.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Low Speed Can Wiring.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0021?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Low Speed Can Wiring.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Low Speed Can Wiring.
  5. 5Clear fault memory and run a verification cycle to confirm U0021 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $227
Professional Repair (Parts + Labor)$54 – $540

Frequently Asked Questions

Is it safe to keep operating with fault code U0021?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair U0021?

DIY replacement parts average $19–$227, while professional service averages $54–$540.

Will resetting U0021 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0021 fault code meaningU0021 repair costhow to fix U0021

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0021 Fault Code: Low Speed CAN Communication Bus (+) Open | FaultCodes.org