FaultCodes.org
U0008OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0008 Fault Code: High Speed CAN Communication Bus (-) High

OBD-II U0008 (CAN Bus & Network Communication): High Speed CAN Communication Bus (-) High.

Quick AnswerHigh — Service Soon

OBD-II fault code U0008 indicates High Speed CAN Communication Bus (-) High. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $86–$1080.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
CAN Bus & Network Communication
Professional Repair
$86 – $1,080

What This Fault Code Means

U0008 means CAN-Low, the (-) wire of the high-speed CAN, is forced too high, typically through contact with the 12 V system or another supply rail. This fault blocks the bus: CAN-Low can no longer be driven down, no dominant state develops, and both onsemi and NXP found that transmission becomes impossible. Senders accumulate errors until they reach bus-off, so U0001 and lost-communication codes nearly always appear alongside, and engine, transmission or brake electronics may switch to stored default values. No manufacturer documents U0008 publicly. With ignition on, CAN-Low reading close to battery voltage instead of about 1.5 to 2.5 V confirms it; the contact point is usually where the bus pair runs beside a supply feed, for example after an accessory installation.

Common Symptoms

  • Total communication loss on the high-speed network
  • Many warning lamps, possible no-start
  • Scan tool cannot reach powertrain modules

Most Likely Root Causes

  • CAN-Low chafed against a battery or ignition supply wire
  • Retrofit wiring tapped into the bus pair by mistake
  • Bent pin or moisture linking CAN-Low to a supply contact

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0008.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Can Low Wire.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0008?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Can Low Wire.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Can Low Wire.
  5. 5Clear fault memory and run a verification cycle to confirm U0008 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $454
Professional Repair (Parts + Labor)$86 – $1,080

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: U0008 (CAN Bus & Network Communication)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $86 – $1,080

Frequently Asked Questions

Is it safe to keep operating with fault code U0008?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair U0008?

DIY replacement parts average $30–$454, while professional service averages $86–$1080.

Will resetting U0008 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0008 fault code meaningU0008 repair costhow to fix U0008

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0008 Fault Code: High Speed CAN Communication Bus (-) High | FaultCodes.org