FaultCodes.org
U0006OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0006 Fault Code: High Speed CAN Communication Bus (-) Open

OBD-II U0006 (CAN Bus & Network Communication): High Speed CAN Communication Bus (-) Open.

Quick AnswerHigh — Service Soon

OBD-II fault code U0006 indicates High Speed CAN Communication Bus (-) Open. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $86–$864.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
CAN Bus & Network Communication
Professional Repair
$86 – $864

What This Fault Code Means

U0006 points to an interrupted CAN-Low conductor, i.e. the (-) line on the high-speed network. That line rests near 2.5 V and sinks by about a volt whenever a dominant bit is sent. Nodes isolated by the break no longer receive a usable differential signal from the rest of the network, while the modules still joined on both wires can go on exchanging data. A line interruption is outside what common high-speed transceivers can diagnose themselves (NXP), so the code relies on module-specific checks such as missing acknowledgements. No manufacturer documents U0006 publicly. Frequent findings are a conductor fractured at a door or tailgate hinge, a backed-out terminal or a corroded splice. With the battery disconnected, a check across the two lines often shows about twice the normal 60 ohms when the break separates one of the terminators.

Common Symptoms

  • Part of the modules unreachable, others still respond
  • Warnings from the affected systems, sometimes only when moving doors or harness

Most Likely Root Causes

  • CAN-Low conductor fractured at a hinge or flex point
  • Corroded splice or connector in the CAN-Low path
  • CAN-Low terminal backed out after work on the harness

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0006.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Can Low Wire.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0006?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Can Low Wire.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Can Low Wire.
  5. 5Clear fault memory and run a verification cycle to confirm U0006 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $363
Professional Repair (Parts + Labor)$86 – $864

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: U0006 (CAN Bus & Network Communication)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $86 – $864

Frequently Asked Questions

Is it safe to keep operating with fault code U0006?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair U0006?

DIY replacement parts average $30–$363, while professional service averages $86–$864.

Will resetting U0006 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0006 fault code meaningU0006 repair costhow to fix U0006

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0006 Fault Code: High Speed CAN Communication Bus (-) Open | FaultCodes.org