FaultCodes.org
U0004OBD-IICAN Bus & Network CommunicationTechnical Reference· Updated: Nov 22, 2026

U0004 Fault Code: High Speed CAN Communication Bus (+) Low

OBD-II U0004 (CAN Bus & Network Communication): High Speed CAN Communication Bus (+) Low.

Quick AnswerHigh — Service Soon

OBD-II fault code U0004 indicates High Speed CAN Communication Bus (+) Low. Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $86–$1080.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
CAN Bus & Network Communication
Professional Repair
$86 – $1,080

What This Fault Code Means

U0004 means the (+) wire of the high-speed CAN, CAN-High, is dragged below its valid range, usually by a short to ground. This is one of the faults the physical layer cannot absorb: a sending node is unable to produce a dominant bit, every frame attempt fails, the error counters rise and the controllers end up bus-off, as onsemi's bench measurements show. Transceivers with bus diagnosis, NXP's TJA1043 for example, recognise this short up to roughly 50 ohms. Typically all powertrain and chassis modules on the network fall silent at the same moment, accompanied by U0001 and a string of lost-communication codes. No manufacturer documents U0004 publicly; an FCA bulletin describes the same picture under U0001, caused by a harness pinched beneath a console bolt.

Common Symptoms

  • Network-wide communication loss, scan tool cannot connect
  • Engine, gearbox, ABS and steering warnings together
  • Vehicle may not start or run in limp mode

Most Likely Root Causes

  • CAN-High insulation damaged and touching body ground
  • Harness clamped by a screw, bracket or seat rail
  • Defective transceiver in one module pulling CAN-High down

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside U0004.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Can High Wire.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside U0004?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Can High Wire.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Can High Wire.
  5. 5Clear fault memory and run a verification cycle to confirm U0004 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$30 – $454
Professional Repair (Parts + Labor)$86 – $1,080

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: U0004 (CAN Bus & Network Communication)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $86 – $1,080

Frequently Asked Questions

Is it safe to keep operating with fault code U0004?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair U0004?

DIY replacement parts average $30–$454, while professional service averages $86–$1080.

Will resetting U0004 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

U0004 fault code meaningU0004 repair costhow to fix U0004

Manufacturer & Technical Reference

OBD-II Technical Reference (CAN Bus & Network Communication)

Related Fault Codes

Auto & OBD-II →
U0004 Fault Code: High Speed CAN Communication Bus (+) Low | FaultCodes.org