FaultCodes.org
P2138OBD-IIPowertrain & Engine ManagementVerified Guide· Updated: Nov 22, 2026

OBD-II P2138: Throttle / Accelerator Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

Dual Accelerator Pedal Position (APP) sensors inside the cabin gas pedal disagree across their 5.0 V reference slopes, forcing immediate Limp Mode / dead throttle—check wet floor-mat corrosion at the pedal plug, 5.0 V ref drop, and smooth APP1 / APP2 live sweeps first.

Quick AnswerCritical — Stop Immediately

Code P2138 (SAE J2012) means the dual Accelerator Pedal Position (`APP "D" / "E"`) sensors inside the cabin gas pedal assembly disagreed across their parallel 5.0 V reference voltage slopes—for instance APP1 climbing ~0.7–4.5 V while APP2 fails to track its proportional ~0.35–2.25 V (or inverted) track—triggering immediate Reduced Engine Power / Limp Mode and a dead or sluggish gas pedal. Before swapping the pedal, inspect the under-dash cabin pedal connector for winter snow-melt/wet floor-mat corrosion or pinched wires, verify clean `5.0 V` reference and ground (low system voltage or shared P0641/P0651 drops can fake P2138), and watch live `APP1` vs `APP2` voltage sweeps KOEO while slowly pressing the pedal ($45–$190 DIY; $190–$480 shop).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Powertrain & Engine Management
Professional Repair
$190 – $480

What This Fault Code Means

In drive-by-wire cars, the cabin accelerator pedal uses two independent internal Hall or potentiometer tracks (APP1 & APP2, typically running in a 2:1 ratio or offset parallel slopes on 5.0 V supplies) so the ECM never guesses driver throttle demand. If wet boot salt corrodes the pedal plug, a shared 5.0 V ref drops out, or internal pedal wiper tracks develop dead spots, voltage correlation fails and the ECM immediately restricts throttle authority via P2138.

Common Symptoms

  • Immediate Reduced Engine Power / Limp Mode warning with zero throttle pedal response or engine stuck at elevated idle (~1,200–1,800 RPM)
  • Sudden loss of acceleration over bumps or during rainy/snowy weather (classic wet cabin pedal plug symptom)
  • Check Engine Light (P2138), often accompanied by P2122/P2127 (APP low/high) or shared 5 V reference codes (P0641/P0651)

Most Likely Root Causes

  • Worn or moisture-damaged internal `APP1 / APP2` tracks inside the cabin accelerator pedal module (#1 cause)
  • Wet floor-mat / winter boot water & salt corroding the cabin pedal plug or harness behind the driver kick panel (classic GM/Nissan/Honda issue)
  • Shared `5.0 V` reference drop (`P0641`/`P0651`) pulled down by another shorted sensor (oil pressure, A/C pressure, or MAP)
  • Chafed firewall grommet wiring or aftermarket floor-mat/cruise-module splice interfering with APP voltage

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Dual APP Track Correlation

Typically ~2:1 voltage ratio (e.g. ~0.7–4.5 V vs ~0.35–2.25 V) or offset tracking

APP1 & APP2 proportional slopes on 5.0 V ref
Failsafe Vehicle Response

ECM ignores conflicting pedal commands to prevent unintended acceleration

Immediate Limp Mode / Dead Throttle Pedal
Cabin Environmental Trigger

Check footwell moisture and sunroof drains before buying a pedal

Wet boot salt / floor-mat water at pedal plug
Shared Circuit Pitfall

Verify 5.0 V ref stability at unplugged pedal before blaming the pedal

5.0 V reference bus sag (P0641 / P0651)

Commonly Affected Models & Service Bulletins

  • Chevrolet / GMC Silverado, Sierra, Impala, Equinox & Malibu (footwell water & APP pedal assembly)
  • Nissan Altima / Maxima / Frontier & Honda Accord / CR-V / Civic (dual APP sensor module)
  • Toyota / Chrysler / Dodge / Jeep / Volkswagen Electronic Accelerator Pedals (SAE J2012)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Check for companion `5 V` reference codes (`P0641`/`P0651`) or `P0562` low battery voltage, then look under the driver dash around the gas pedal plug for damp carpet, green connector corrosion, or chafed wires.
  2. 2Turn Key ON Engine OFF (KOEO) and graph live scan `APP1` (`D`) and `APP2` (`E`) voltages while slowly pressing the pedal smoothly from 0% to 100% 3–4 times: look for dropouts, flat spots, or disproportionate APP1/APP2 voltage ratios (also wiggle the cabin pedal plug).
  3. 3Back-probe the 6-pin pedal connector with a multimeter to verify steady `5.0 V` reference(s) and < 0.1 V ground return while sweeping both signal pins.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Is the driver footwell/pedal plug damp or green-corroded, OR do APP1/APP2 glitch when wiggling the cabin pedal connector?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live-data scanner (APP1/APP2 live voltage graph during slow pedal sweep)Digital multimeter (5.0 V reference check, ground drop & back-probe pins)Electrical contact cleaner & OEM 6-pin pedal pigtail (if footwell corrosion found)
  1. 1Dry wet driver-side carpet/underlayment, remove any green oxidation from the cabin APP connector, and replace corroded terminal pins or a damaged pedal pigtail harness.
  2. 2If either 5.0 V ref sags below 4.8 V, unplug suspect shared 5 V sensors (A/C transducer, MAP, oil pressure) one by one until 5.0 V returns.
  3. 3If 5.0 V reference and ground hold rock-steady yet APP1 or APP2 drops out or diverges during slow KOEO sweeps, unbolt the 2–3 mounting nuts and install an OEM Accelerator Pedal Assembly.
  4. 4Clear P2138, confirm smooth proportional APP1/APP2 sweeps across full pedal travel, and perform any OEM pedal/throttle relearn if required.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$45 – $190
Professional Repair (Parts + Labor)$190 – $480

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Is it safe to drive with P2138?

No—P2138 triggers Reduced Engine Power / Limp Mode and can drop throttle pedal response to zero mid-intersection or highway merge. Park safely and repair it before normal driving.

What is the difference between P2138 and P2135?

P2138 ("D"/"E") monitors the cabin Accelerator Pedal (`APP`) sensor at your foot, whereas P2135 ("A"/"B") monitors the Electronic Throttle Body (`ETB`) sensor under the hood.

Related Searches & Questions

OBD2 P2138 accelerator pedal position sensor fixP2138 vs P2135 difference throttle vs pedalP2138 APP1 APP2 voltage sweep 5V referenceP2138 wet floor mat connector limp mode cost

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P2138: Throttle / Accelerator Pedal Position… — Fixes & Cost | FaultCodes.org