# OBD-II P2138: OBD-II P2138: Throttle / Accelerator Pedal Position Sensor / Switch "D" / "E" Voltage Correlation

> **Quick Answer:** Code **P2138** (SAE J2012) means the dual **Accelerator Pedal Position (`APP "D" / "E"`) sensors** inside the cabin gas pedal assembly disagreed across their parallel `5.0 V` reference voltage slopes—for instance `APP1` climbing `~0.7–4.5 V` while `APP2` fails to track its proportional `~0.35–2.25 V` (or inverted) track—triggering **immediate Reduced Engine Power / Limp Mode** and a dead or sluggish gas pedal. Before swapping the pedal, inspect the **under-dash cabin pedal connector for winter snow-melt/wet floor-mat corrosion** or pinched wires, verify **clean `5.0 V` reference and ground** (low system voltage or shared `P0641`/`P0651` drops can fake `P2138`), and watch live **`APP1` vs `APP2` voltage sweeps** KOEO while slowly pressing the pedal ($45–$190 DIY; $190–$480 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p2138
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** Powertrain & Engine Management
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
In drive-by-wire cars, the cabin accelerator pedal uses two independent internal Hall or potentiometer tracks (`APP1` & `APP2`, typically running in a 2:1 ratio or offset parallel slopes on `5.0 V` supplies) so the ECM never guesses driver throttle demand. If wet boot salt corrodes the pedal plug, a shared `5.0 V` ref drops out, or internal pedal wiper tracks develop dead spots, voltage correlation fails and the ECM immediately restricts throttle authority via `P2138`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Dual APP Track Correlation | APP1 & APP2 proportional slopes on 5.0 V ref | Typically ~2:1 voltage ratio (e.g. ~0.7–4.5 V vs ~0.35–2.25 V) or offset tracking |
| Failsafe Vehicle Response | Immediate Limp Mode / Dead Throttle Pedal | ECM ignores conflicting pedal commands to prevent unintended acceleration |
| Cabin Environmental Trigger | Wet boot salt / floor-mat water at pedal plug | Check footwell moisture and sunroof drains before buying a pedal |
| Shared Circuit Pitfall | 5.0 V reference bus sag (P0641 / P0651) | Verify 5.0 V ref stability at unplugged pedal before blaming the pedal |

## Commonly Affected Models & Service Bulletins
- Chevrolet / GMC Silverado, Sierra, Impala, Equinox & Malibu (footwell water & APP pedal assembly)
- Nissan Altima / Maxima / Frontier & Honda Accord / CR-V / Civic (dual APP sensor module)
- Toyota / Chrysler / Dodge / Jeep / Volkswagen Electronic Accelerator Pedals (SAE J2012)

## Common Symptoms
- Immediate **Reduced Engine Power / Limp Mode** warning with **zero throttle pedal response** or engine stuck at elevated idle (`~1,200–1,800 RPM`)
- Sudden loss of acceleration over bumps or during rainy/snowy weather (classic wet cabin pedal plug symptom)
- Check Engine Light (`P2138`), often accompanied by `P2122`/`P2127` (`APP` low/high) or shared `5 V` reference codes (`P0641`/`P0651`)

## Most Likely Root Causes
- **Worn or moisture-damaged internal `APP1 / APP2` tracks** inside the cabin accelerator pedal module (#1 cause)
- **Wet floor-mat / winter boot water & salt corroding the cabin pedal plug** or harness behind the driver kick panel (classic GM/Nissan/Honda issue)
- Shared **`5.0 V` reference drop (`P0641`/`P0651`)** pulled down by another shorted sensor (oil pressure, A/C pressure, or MAP)
- Chafed firewall grommet wiring or aftermarket floor-mat/cruise-module splice interfering with `APP` voltage

## Tools & Parts Reference
- OBD-II live-data scanner (`APP1`/`APP2` live voltage graph during slow pedal sweep)
- Digital multimeter (`5.0 V` reference check, ground drop & back-probe pins)
- Electrical contact cleaner & OEM 6-pin pedal pigtail (if footwell corrosion found)

## Step-by-Step Troubleshooting & Fix
1. Dry wet driver-side carpet/underlayment, remove any green oxidation from the **cabin APP connector**, and replace corroded terminal pins or a damaged pedal pigtail harness.
2. If either `5.0 V` ref sags below `4.8 V`, unplug suspect shared `5 V` sensors (A/C transducer, MAP, oil pressure) one by one until `5.0 V` returns.
3. If `5.0 V` reference and ground hold rock-steady yet `APP1` or `APP2` drops out or diverges during slow KOEO sweeps, unbolt the 2–3 mounting nuts and install an **OEM Accelerator Pedal Assembly**.
4. Clear `P2138`, confirm smooth proportional `APP1/APP2` sweeps across full pedal travel, and perform any OEM pedal/throttle relearn if required.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $45–$190 | $190–$480 |
| GBP | £36–£150 | £150–£375 |
| CAD | CA$60–CA$250 | CA$250–CA$625 |
| EUR | €42–€175 | €175–€430 |
| CHF | CHF 50–CHF 210 | CHF 225–CHF 540 |

## Frequently Asked Questions
### Is it safe to drive with P2138?
No—`P2138` triggers **Reduced Engine Power / Limp Mode** and can drop throttle pedal response to zero mid-intersection or highway merge. Park safely and repair it before normal driving.

### What is the difference between P2138 and P2135?
`P2138` (`"D"/"E"`) monitors the **cabin Accelerator Pedal (`APP`) sensor at your foot**, whereas `P2135` (`"A"/"B"`) monitors the **Electronic Throttle Body (`ETB`) sensor under the hood**.


## Verified Official & Engineering References
- [US EPA On-Board Diagnostics (OBD) Standards](https://www.epa.gov/obd) (Regulation / Standard)
- [SAE International: SAE J2012 Diagnostic Trouble Code Standards](https://www.sae.org/standards/content/j2012/) (Regulation / Standard)
- [NHTSA Vehicle Safety & Emissions Recalls / TSB Portal](https://www.nhtsa.gov/recalls) (Official Support)
