FaultCodes.org
P2135OBD-IIPowertrain & Engine ManagementVerified Guide· Updated: Nov 22, 2026

OBD-II P2135: Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation

Drive-by-wire Electronic Throttle Body dual TPS tracks diverge (TPS1 ~0.5->4.5 V vs TPS2 ~4.5->0.5 V on 5.0 V ref), triggering instant Reduced Engine Power / Limp Mode—check battery voltage (P0562) and corroded throttle pigtails before replacing the ETB + performing Idle Relearn.

Quick AnswerCritical — Stop Immediately

Code P2135 (SAE J2012) means the dual internal Throttle Position Sensors (`TPS "A" / "B"`) mounted on the drive-by-wire Electronic Throttle Body (`ETB`) disagreed beyond safety limits—for example, TPS1 rising ~0.5->4.5 V vs TPS2 falling ~4.5->0.5 V on a shared 5.0 V reference—forcing immediate Reduced Engine Power / Limp Mode (~1,200–2,000 RPM cap). Check battery & charging health (`P0562`) FIRST, because weak 5 V voltage during cranking trips false P2135. Next, inspect the 6-pin throttle body connector pigtail for terminal fretting or moisture corrosion, check for a carbon-binding throttle plate, and if TPS1/TPS2 tracks diverge during a slow KOEO sweep, replace the Electronic Throttle Body (or pigtail) and perform an Idle Air Volume / Throttle Relearn ($15–$260 DIY; $220–$640 shop).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Powertrain & Engine Management
Professional Repair
$220 – $640

What This Fault Code Means

Because electronic drive-by-wire systems have no steel accelerator cable, the ECM demands redundant opposite-slope feedback (TPS1 + TPS2 ≈ 5.0 V) inside the throttle housing to verify exact throttle blade angle. Even a brief > 0.25–0.50 V mismatch from dirty potentiometer tracks, fretted connector pins, or sticky carbon holding the blade against motor commands triggers P2135 and locks out normal throttle response for safety.

Common Symptoms

  • Immediate Reduced Engine Power / Limp Mode warning (ETC lightning bolt or wrench light) with dead or sluggish throttle
  • High or hunting idle (1,200–1,800 RPM), stalling at stops, or inability to rev past ~2,000–2,500 RPM
  • Often returns after cold damp mornings, bumps (loose throttle pigtail), or low battery starts (P0562)

Most Likely Root Causes

  • Fretted, oxidized, or loose 6-pin Electronic Throttle Body (`ETB`) connector pigtail (#1 overlooked repair on GM/Chrysler/Nissan)
  • Worn or moisture-contaminated internal dual TPS tracks (`TPS1 / TPS2`) inside the Electronic Throttle Body
  • Heavy black carbon ridge binding the throttle blade around the bore so actual opening lags motor command
  • Low battery/charging voltage (`P0562`) or shared `5.0 V` sensor reference drop (`P0641`) skewing TPS1/TPS2

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Dual TPS Correlation Logic

Inverse dual-track redundancy on 5.0 V ref; > ~0.25–0.5 V mismatch sets P2135

TPS1 ~0.5->4.5 V vs TPS2 ~4.5->0.5 V (sum ~5.0 V)
Failsafe Vehicle Response

Prevents unintended acceleration when redundant blade position feedback disagrees

Immediate Reduced Engine Power / Limp Mode
Mandatory Post-Repair Step

Required after cleaning or ETB swap so ECM learns closed-stop offset

Throttle Body / Idle Air Volume Relearn
Primary Non-ETB Suspects

Always check before spending money on a full Electronic Throttle Body

Low battery (P0562) & fretted 6-pin ETB pigtail

Commonly Affected Models & Service Bulletins

  • Chevrolet / GMC Silverado, Tahoe, Equinox, Malibu & Trailblazer (6-pin ETB pigtail & throttle body)
  • Chrysler / Dodge / Jeep / Ram Hemi & Pentastar ETC Systems (TPS A/B correlation)
  • Nissan / Honda / Toyota / Ford Drive-by-Wire Throttle Bodies (SAE J2012)

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Check battery resting/cranking voltage (> 12.4 V resting, 13.5–14.5 V running) and check for P0562 or P0641 (5 V reference fault) before touching the throttle body.
  2. 2Graph live scan `TPS1` and `TPS2` voltages (or %) KOEO while slowly pressing the gas pedal from 0% to 100% (or gently moving blade unplugged/key-on if safe): confirm smooth opposing curves (~0.5->4.5 V vs ~4.5->0.5 V, sum staying ~5.0 V) while wiggling the throttle pigtail harness.
  3. 3Unplug the 6-pin ETB connector to inspect for green oxidation or spread female terminals, verify clean `5.0 V` reference and < 0.1 V ground, and inspect the throttle bore edge for sticky carbon varnish.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Does P0562 (low voltage) or P0641 (5 V reference fault) appear alongside P2135, OR does wiggling the 6-pin ETB plug glitch TPS1/TPS2?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

OBD-II live-data scanner (TPS1 & TPS2 voltage graph + Throttle/Idle Relearn function)Digital multimeter (5.0 V reference, ground & terminal pin-drag check)Throttle-body cleaner, lint-free rags & replacement OEM pigtail kit (if corroded)
  1. 1If wiggling the throttle harness makes TPS1/TPS2 spike—or pins look darkened/spread—install a new OEM throttle-body connector pigtail kit with staggered heat-shrink splices and dielectric contact lube.
  2. 2Disconnect negative battery terminal, remove intake boot, and gently clean thick black carbon buildup from the throttle bore and brass/aluminum blade edge using throttle-body cleaner on a lint-free rag (avoid flooding the electronics housing!).
  3. 3If the 5.0 V ref, ground, and pigtail test solid yet TPS1 and TPS2 still diverge or glitch during sweeps, replace the Electronic Throttle Body assembly (or bolt-on TPS module where serviceable).
  4. 4Clear P2135 and ALWAYS execute the factory Idle Air Volume / Throttle Body Relearn (key-on wait / scan-tool relearn or drive cycle) so idle settles smoothly.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$15 – $260
Professional Repair (Parts + Labor)$220 – $640

Recommended Diagnostic Tools & Replacement Parts

Check OEM specifications and compatible tools for this repair.

Frequently Asked Questions

Is it safe to drive when Reduced Engine Power (P2135) activates?

No—P2135 locks the engine into Limp Mode with severely limited acceleration or sudden stalling, making highway merges and intersections unsafe until repaired.

What is the difference between P2135 and P2138?

P2135 (TPS "A"/"B") occurs at the Electronic Throttle Body under the hood, whereas P2138 (APP "D"/"E") occurs inside the cabin at the Accelerator Gas Pedal sensor.

Related Searches & Questions

OBD2 P2135 throttle position sensor correlation fixP2135 reduced engine power limp mode pigtailP2135 TPS1 TPS2 voltage 0.5 to 4.5V testP2135 throttle body idle relearn repair cost

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

Auto & OBD-II →
OBD-II P2135: Throttle / Pedal Position Sensor /… — Fixes & Cost | FaultCodes.org